Definitive Technology 2500 owner manual Powering Up the Active Subwoofer Section

Page 11

Setting Bass and Treble Controls on Your Receiver or Amplifier

Normally we recommend that you set the Bass and Treble controls on flat or 0 dB. This will give you the most linear and natural sound. If you want more bass, raise the subwoofer’s Level control on your C/L/R 2500, keeping in mind that even a little turn of the knob can make a big difference in the sound. Also, if your amplifier or receiver has a graphic equalizer, we recom- mend that you leave it flat. The reason for this is that we have spoken with many consumers about what they thought were improperly sounding speakers when in fact the problem was misadjusted tone controls. When in doubt, leave them flat; this almost always sounds the best.

Powering Up the Active Subwoofer Section

Your C/L/R 2500(s) contains a built-in, active powered subwoofer section as well as an electronic crossover and so each C/L/R 2500 must be plugged into an electrical socket of the appropriate voltage (as indicated on the back of your unit) using the plug on the end of the black cord attached to the electronics module on the back of the loudspeaker. The C/L/R 2500 has a special circuit which automati- cally turns the powered subwoofer section on when a signal is fed to the loud- speaker and does not require an on-off switch. The red LED on the back panel will light up when a signal is sensed and the amplifier turns on. Please note that after the cessation of a signal, it may take up to an hour for the amplifier to actually turn off.

Setting Your C/L/R 2500’s Low-Frequency Level Control

Your C/L/R 2500 has a level control for the electronic crossover which allows you to perfectly tune the output level of the powered low frequency subwoofer section to match your room as well as to fulfill your own personal listening pref- erences. Please note that there are no controls to vary the crossover points or

phase because these have been factory set to provide perfect blending (a major performance benefit of this innovative product). When using the speaker wire input, we suggest beginning with the level control set at approximately 1 o’clock. However, when using the “Full Range Low Level In” with the jumpers

removed between “Mid” and “Low,” the level control starting point position may vary and you must experiment for optimum setting. Set the level control so that the sound is most pleasing to you. In general, when used as a center channel, the C/L/R 2500 subwoofer should not be turned up excessively high to add more “room shaking level bass” but should be kept in proper balance with the upper bass/midrange drivers in order to achieve properly balanced high- impact full-range center channel presentation.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Registered Trademark Safety Precautions Speaker Break-in Unpacking Your C/L/RCLR 2500 Center Channel Rear PanelConnecting Each Speaker with One Pair of Speaker Wires Only Bi- or Tri-Wiring Diagram # 3 Tri-Wiring Connector Amp-In Center Pre-Out Center Pre-Amplifier Using Your C/L/R 2500s in a Dolby Digital AC-3 System Setting Your C/L/R 2500’s Low-Frequency Level Control Powering Up the Active Subwoofer SectionPositioning the C/L/R 2500s in Your Room Technical Assistance Service Installing the LogoInstalling the Feet/Angling Device Driver Complement R 2500 Specifications

2500 specifications

The Definitive Technology BP-2500 is a high-performance loudspeaker that embodies the brand's commitment to delivering outstanding audio quality and innovative design. Renowned for its powerful sound and sleek aesthetics, the BP-2500 is a prime choice for both audiophiles and casual listeners alike.

One of the standout features of the BP-2500 is its unique bipolar speaker design. This innovative layout incorporates both front- and rear-facing drivers, creating a more immersive soundstage that allows for better sound dispersion around the room. The result is a rich, enveloping sound that fills any space, making it ideal for home theater setups as well as music listening.

The BP-2500 is equipped with a 12-inch bass driver, which provides deep, impactful low frequencies. This driver is paired with a high-output 1-inch aluminum dome tweeter, offering crisp, clear highs that perfectly balance the overall sound signature. The combination of these drivers allows the BP-2500 to reproduce a wide frequency range, ensuring that every note and detail in your music or movie is accurately conveyed.

Another key characteristic of the BP-2500 is its built-in powered subwoofer. This feature not only enhances the bass response significantly but also eliminates the need for an external subwoofer, saving space in your audio setup. The integrated 250-watt amplifier ensures that the subwoofer delivers punchy, dynamic bass without distortion, even at higher volumes.

Definitive Technology also incorporates advanced technologies like their proprietary "Forward-Focused Bipolar Array" in the BP-2500. This technology is designed to minimize reflections from walls, ensuring that the audio you hear is as close to the original recording as possible. The result is a more accurate and lifelike representation of your favorite music and movies.

The aesthetic appeal of the BP-2500 is also noteworthy. With its elegant cabinet design and premium finish options, this loudspeaker not only sounds great but also looks stunning in any room. The design is both functional and stylish, making it a perfect addition to modern home decor.

In summary, the Definitive Technology BP-2500 offers a powerful combination of innovative design, advanced audio technologies, and stunning aesthetics, making it a top contender in the world of high-performance loudspeakers. Whether you’re a serious audiophile or simply someone who enjoys high-quality sound, the BP-2500 is sure to impress.
Top Page Image Contents