Table 2. Internal Switch Option Settings
Switch | Label | Function |
|
| Description |
|
|
| |
|
|
|
|
|
|
| |||
B1 | Service Level Selection |
| Selects the service level. The |
|
| ||||
B2 |
|
| optioned to deliver full ISDN (2B+D) or any of the |
|
| ||||
D |
|
| following levels of service. |
|
|
|
| ||
|
|
|
| Service Type | Service |
| |||
|
|
|
| Option | (B1) | (B2) | (D) |
| |
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ISDN | *2B+D | On | On | On |
|
|
|
|
| Leased (128 kbps) | 2B | On | On | Off |
|
|
|
|
| ISDN/ DDS | B1+D | On | Off | On |
|
|
|
|
| ISDN | B2+D | Off | On | On |
|
|
|
|
| DDS/Leased | B1 | On | Off | Off |
|
|
|
|
| Leased | B2 | Off | On | Off |
|
|
|
|
| ISDN | D | Off | Off | On |
|
|
|
|
|
|
| ||||
|
|
| In 2B+D, B1+D, or B2+D the ZBS option must be set the same |
| |||||
On | ZBS EN | Enables ZBS |
| for the COT and RT. |
| ||||
|
|
|
| for |
| ||||
Off | ZBS DIS* | Disables ZBS |
|
| |||||
| be disabled when DDS service rate is 64 kbps, or 56 kbps with |
| |||||||
|
|
|
|
| |||||
|
|
|
| secondary channel. Consult local provisioning guidelines. |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Off | NORM* | Normal |
| No powering provided toward the customer |
| ||||
On | POWER | Powering provided toward |
| Automatically determines which of the following modes of |
| ||||
|
| the customer |
| operation is appropriate; |
|
|
|
| |
|
|
|
| • Supply a constant 43 mA to power an ADTRAN ISDN |
| ||||
|
|
|
|
|
| ||||
|
|
|
| • Supply a constant |
| ||||
|
|
|
| IDSL |
|
|
|
|
|
|
|
|
|
|
|
| |||
| Termination Mode |
| This switch should be set toward "LULT" | when the unit is |
| ||||
On | LULT (RT)* | LULT Mode (RT typical) |
| installed as |
| ||||
|
|
|
| or Tandem Office Source configuration. This switch |
| ||||
Off | LUNT (COT) | LUNT Mode (COT) |
| should be set toward "LUNT" | for |
| |||
|
|
|
| Tandem Office Sink configurations (See Figure 5). |
|
| |||
|
|
|
|
|
| ||||
| LULT Mode |
| In the LULT(RT) mode, |
| |||||
On | ADJ* | DC sealing current provided |
| When used in an |
| ||||
|
|
|
| sealing current should be provided |
| ||||
Off | TANDEM | DC sealing current not |
| Tandem Office Source, sealing current is not required, and |
| ||||
|
| provided |
| should be disabled |
|
| |||
On | ADJ | LUNT Mode |
| In the LUNT(COT) mode, |
| ||||
|
| Periodic | up tone. Periodic |
| |||||
|
| provided |
| located in an |
| ||||
Off | TANDEM |
|
| Periodic |
| ||||
|
| Periodic |
| located in a Tandem Office Sink configuration, or when |
| ||||
|
| provided |
| adjacent to a device requiring |
| ||||
|
|
|
| Newbridge switch (See Figure 5). |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
Note: Power option should only be used in the LULT (RT) configuration.
*Factory Setting
Section | 5 |