Asus M2A690G installation manual Internal Audio Connector

Page 65

8. Optical drive audio connector (4-pin CD1)

This connector is for the 4-pin audio cable that connects to the audio connector at the back of the optical drive.

M2A-VM

Internal Audio Connector

CD (black)

Channel Ground

Ground

Channel

Left Audio

Right Audio

Enable the CD-IN function in the audio utility when using this connector.

9. USB connectors (10-1 pin USB56, USB78, USB910)

These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specification that supports up to 480 Mbps connection speed.

USB+5V _USB USBP6+ GND NC

USB+5V _USB USBP8+ GND NC

USB+5V _USB USBP10+ GND NC

P6-

P8-

P10-

M2A-VM

USB561

USB781

USB9101

_ GND

_ GND

_ GND

P5- P5+

P7- P7+

P9- P9+

USB+5V _

USB+5V _

USB+5V _

USB

USB

USB

USB

USB

USB

USB 2.0 Connectors

Never connect a 1394 cable to the USB connectors. Doing so will damage the motherboard!

The USB module is purchased separately.

4-10

Chapter 4: Motherboard info

Page 64 Page 66
Image 65
Page 64 Page 66
Contents Series M2A690G E3061 First Edition February Table of contents Motherboard Info Chapter Bios InformationChapter Starting up Onboard Device Configuration Canadian Department of Communications Statement Federal Communications Commission StatementOperation safety Safety informationElectrical safety How this guide is organized About this guideAudience Conventions used in this guide Where to find more informationSystem package contents System introduction Front panel WelcomePage Rear panel Audio 2, 4, or 6-channel configuration Voltage selector Hdmi card portsInternal components System introduction Basic installation Preparation Basic components to installBefore you proceed ToolRemoving the side cover and front panel assembly Central Processing Unit CPU Installing the CPUGold triangle Small triangle Installing the heatsink and fan Page Memory configurations Installing a DimmDDR2-667 Qualified Vendors Lists QVL DDR2-533KHX6400D2LLK2/1GN DDR2-800Removing a DDR2 Dimm Installing a DDR2 DimmExpansion slots Installing an expansion cardConfiguring an expansion card IRQ assignments for this motherboard Standard interrupt assignmentsPCI Express x16 slot PCI Express x1 slotPCI slots Installing an optical drive Installing a hard disk drive Serial ATA power Serial ATA cable Cable Installing the card reader Asus V-Series M2A690G Installing a floppy disk drive LED cables Re-connecting cablesReinstalling the cover Asus V -Series M2A690G Starting up Support CD information Installing an operating systemPowering up Running the support CD Drivers menu Utilities menu Manual menu Make Disk menuMake ATI RAID/AHCI Driver Make ATI RAID/AHCI Vista DriverAsus Contact information Using PC Probe Installing PC ProbeSoftware information Asus PC ProbeSensor alert PreferencesChanging the monitor panels position Hardware monitor panelsDMI browser WMI browserUsage PCI browserMemory usage Configuring PC ProbeStarting up Motherboard introduction Motherboard layout IntroductionClear RTC RAM Clrtc JumpersUSB Device Wake Up Connectors PRI IDE COM Port Connector Ieee 1394a Connector ATX Power Connector Internal Audio Connector Azalia Analog Front Panel Connector Power/Soft-off button 2-pin Pwrsw C d Playback of HD DVD and Blu-Ray Discs Dual display tableBios setup Creating a bootable floppy disk Managing and updating your BiosPath A\ Asus EZ Flash 2 utilityEnter. The Award Bios Flash Utility screen appears Award Bios Flash UtilityNo Update Write Fail Recovering the Bios from a floppy/USB flash disk Asus CrashFree Bios 3 utilityRecovering the Bios from the support CD Page Installing Asus Update Asus Update utilityUpdating the Bios through the Internet Updating the Bios through a Bios file Menu bar Bios setup programBios menu screen Sub-menu items Configuration fieldsMenu items General help Pop-up windowSystem Time Main menuSystem Date Day xx/xx/xxxx Legacy Diskette a 1 .44M, 3.5Primary IDE Master/Slave Auto Access Mode AutoPrimary IDE Master/Slave Udma Mode Auto PIO Mode AutoTransfer Mode CapacityExtended Drive Auto SataInstalled Memory xxx MB HDD Smart Monitoring DisabledUsable Memory XXX MB Landing ZoneAdvanced menu JumperFree Configuration+1.2VNBSB Auto DDR2 Voltage Control AutoCPU Configuration LDT & PCI Bus Control Dram ConfigurationChipset UMA Frame Buffer Size 64MB Surroundview DisabledSpread Spectrum Auto Plug & Play O/S NoMaximum Payload Size PCI Latenct Timer CLKIRQ Resources South OnChip IDE Device Onboard LAN EnabledSouth OnChip PCI Device Front Panel Type HD AudioUSB Configuration Acpi Apic Support Enabled Power menuAPM Configuration Acpi Suspend Type S1&S3Restore on AC Power Loss Power Off Power On By External Modem DisabledPower Up On PCI/PCIE Devices Disabled Hpet Support EnabledHardware Monitor Fan Controller DisabledCPU Fan Type DC CPU Temperature, MB TemperatureVcore Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage CPU Fan Speed warning 800 RPM1st ~ 4th Boot Device Removable Boot menuRemovable Drives Floppy DisksQuick Boot Enabled Case Open Warning EnabledBoot Up Floppy Seek Disabled Hard Disk DrivesTypematic Rate Setting Disabled Bootup Num-Lock OnFull Screen Logo Enabled OS Select for Dram 64MB Non -OS2Password Check Supervisor Password User PasswordTools menu Asus Music AlarmRepeat Track Disabled Alarm Time hhmm 0Volume Audio CD Drive Primary IDE MasterLoad from File Load Bios ProfileLoad from Profile 1/2 Save to File Save Bios ProfileSave to Profile 1/2 Asus EZ Flash Exit menuExit & Save Changes Load Setup DefaultsExit & Discard Changes Discard Changes
Top Page Image Contents