Carson SC-407 operating instructions Installation

Page 4

Page 4 of 12

SC-407-10 Ver. B Installation and Operating Instructions

INSTALLATION

Proper installation of the unit is essential for years of safe, reliable operation. Please read all instruction before installing the unit. Failure to follow these instructions can cause serious dam- age to the unit or vehicle and may void warranties.

SAFETY PRECAUTIONS

For the safety of the installer, vehicle operator, passengers and the community please observe the following safety precautions. Failure to follow all safety precautions and instructions may result in property damage, injury or death.

Qualifications - The installer must have a firm knowledge of basic electricity, vehicle electrical systems and emergency equipment.

Sound Hazard - Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage. Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity. (Ref. OSHA 1910.95 for occupational noise exposure guidelines)

Mounting - Mount the unit for easy access by the vehicle operator. DO NOT mount in air bag deployment area. Assure clearances before drilling in vehicle. To prevent internal damage mounting bolts must not enter case more than 1/4".

Wiring - Use wiring capable of handling the current required. Make sure all connections are tight. Route wiring to prevent wear, overheating and interference with air bag deployment. Install and check all wiring before connection to vehicle battery.

Testing - Test all siren functions after installation to assure proper operation. Test vehicle opera- tion to assure no damage to vehicle.

Keep These Instructions - Keep these instructions in the vehicle or other safe place for future reference. Advise the vehicle operator of the location.

UNPACKING

Inspect contents for shipping damage. If found alert carrier immediately. Contents should in- clude unit with attached microphone, mounting bracket, microphone bracket with 2 screws, 2 mounting bolts, removable terminal block plug, and these instructions. Contact supplier immedi- ately if any components are missing.

MOUNTING

The mounting bracket supplied can be installed above or below the unit. Choose a mounting location convenient to the operator and away from any air bag deployment areas. Inspect behind mounting area for clearance. Assure adequate ventilation to prevent overheating. Consider wire routing and access to connections, as well as microphone bracket placement. Install mounting bracket to vehicle using 1/4" hardware (not supplied).

If mounting in a rack or console, make sure that mounting bolts do not enter case more than 1/4".

INSTALLER-SELECTABLE OPTIONS

 

 

 

 

 

 

 

 

 

 

 

Carefully cutting programming resistor jumpers

 

 

 

 

 

 

 

 

 

 

 

or traces on the printed circuit board inside the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

case can select various options.

 

 

 

 

 

 

 

 

 

 

 

Cover Removal - The cover is held in place by

 

 

 

 

 

 

 

 

 

 

 

a snap-fastener on the back of the unit. Hold

 

 

 

 

 

 

 

 

 

 

 

the unit with the front case flange on the edge

 

 

AUXP

 

CUTP

T-T AUXI PHSR

of a hard surface and press hard on the back of

 

 

 

the unit. The chassis will slide out the front of

 

 

 

 

 

 

 

 

 

 

 

the cover.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Auxiliary Input Function - The auxiliary input

 

OPTION JUMPERS

 

 

 

 

 

normally activates the Horn function. To acti-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

vate the Man/Phsr function with the auxiliary

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

input cut the jumper resistor labeled "AUX I".

 

 

 

 

 

 

 

 

 

 

 

Auxiliary Input Polarity - The auxiliary input is normally activated by connecting to positive. To activate by connecting to ground cut the two jumper resistors labeled "AUX P".

Cutout Input Polarity - The cutout input is normally activated by connecting to positive. To acti- vate by connecting to ground cut the two jumper resistors labeled "CUT P".

Two-Tone- Two-Tone can replace Phaser by cutting the jumper resistor labeled "T-T".

Phaser Disable - The Phaser function can be completely disabled by cutting the jumper resistor labeled "PHSR".

05/07/05

CP4842C

Image 4
Contents SC-407 Ver. B Phone 888 577-6877 Fax 317Table of Contents Specifications General DescriptionSiren Section Light Control SectionInstallation Siren Connections Spkr Spkr POS POS RAD RAD AUX CUT NEG NEGConnections AT Rear of Unit with PIN Terminal Block Plug CP4688-10Recommended Wire Size Light Control ConnectionsFuses / Breakers Amps SizeLight Control Rocker Switch Connections Switch Lead SetsRecommended Wire Size Amps Size Switch Leads HoleOperation Lever Switch Rocker SwitchesHorn Ring Cycler 2 Optional Light System ControlsProblems ServiceSymptom Possible Cause Check Installation Information Lever SwitchRocker Switches PartsLimited Warranty Return
Related manuals
Manual 12 pages 29.99 Kb

SC-407 specifications

The Carson SC-407 is a versatile and compact scanner that stands out in today's market for its robust features and advanced technologies. Designed for both personal and professional use, this scanner combines efficiency with high-quality output, making it an ideal choice for users in various fields, including education, business, and healthcare.

One of the main features of the SC-407 is its impressive scanning speed. Capable of handling up to 30 pages per minute, this scanner ensures that even large document batches can be processed quickly without sacrificing quality. This speed is further complemented by its ability to scan both sides of a page simultaneously, thanks to the built-in duplex scanning technology. This feature not only enhances productivity but also reduces the time spent on repetitive tasks.

In terms of connectivity, the Carson SC-407 offers multiple options, making it incredibly user-friendly. Equipped with USB 3.0, users can connect the scanner to their computers with ease. Additionally, it supports wireless connectivity, allowing for scanning directly to cloud services or smartphones without the need for a physical connection. This flexibility caters to the modern user’s need for convenience and mobility.

Quality is paramount in the SC-407’s design. It boasts a high resolution of up to 600 dpi, ensuring that scanned documents are clear and crisp. This feature is particularly beneficial for scanning detailed images, graphics, or text documents that require precision. Furthermore, the scanner includes advanced image enhancement technologies, such as automatic color detection and background removal, which improve the visual quality of the scans.

Another notable characteristic of the SC-407 is its compact design. Lightweight and easily portable, it can fit seamlessly into any workspace environment. This is particularly advantageous for users with limited desk space or those who need to take their scanner on the go.

In conclusion, the Carson SC-407 combines speed, quality, and versatility in a compact package. Its advanced features, including duplex scanning, high-resolution output, and multiple connectivity options, make it an indispensable tool for anyone looking to streamline their document management process and enhance productivity in an increasingly digital world. Whether for personal or professional use, the SC-407 is designed to meet the needs of today's users effectively and efficiently.