GX-60C Amplifier
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 17 | 18 | 19 | 20 | 21 |
FRONT PANEL:
1:INPUT: Connect your guitar here using a shielded instrument cable.
CHANNEL A: A high gain channel giving you sounds from a slight edge to serious overdrive.
2:GAIN: Sets the amount of compression and distortion from the amplifier. At far left, the sound will have a thick compressed quality. As you turn the control to the right the amount of distortion increases. Use this along with the Shape and Level controls (#3 and 7) to create a wide vari- ety of sounds.
3:SHAPE: Rotate the Shape control until you find the sound you’re looking for. Turning the control towards the left enhances the mid frequencies; turning it to the right enhances the low and high frequencies. Controlled by the Shape Active switch (#4).
4:SHAPE ACTIVE: Boosts the gain of Channel A and activates the Shape control (#3). A footswitch (see #29, rear panel) overrides this switch.
5:LOW: Adjusts the low frequency output level: to the left reduces the low frequency output; to the right increases it. This control allows a range of 10dB at 80Hz.
6:HIGH: Adjusts the high frequency output level: to the left reduces the high frequency output, to the right increases it. This control allows a range of 10dB at 7kHz.
7:LEVEL: Sets the output volume level from Channel A: in the
8:CHANNEL SELECT: When this switch is pressed in Channel A is engaged. Channel B is selected when this switch is out. A footswitch (see #29, rear panel) overrides this switch. The adjacent LEDs indicate which channel is selected.
CHANNEL B: A normal gain channel designed to give you crystal clear sounds.
9:LEVEL: Sets the output volume level from Channel B: in the
10:LOW: Adjusts the low frequency output level: to the left reduces the low frequency output; to the right increases it. This control allows a range of 20dB at 100Hz.
11:MID: Adjusts the mid frequency output level: to the left reduces the midrange output; turning it to the right increas- es it. This control allows a range of 14dB at 700Hz.
12:HIGH: Adjusts the high frequency output level: to the left reduces the high frequency output; to the right increas- es it. This control allows a range of 27dB at 10kHz.
13:REVERB A: Adjust the amount of reverb for Channel A with this control: in the
14:REVERB B: Adjust the amount of reverb for Channel B with this control: in the
15:INSERT LOOP: Connect an external effects device via this jack. Use a stereo 1/4” male
16:CHORUS ON/OFF: Turn the Chorus/Expander on and off with this switch. When the switch is pressed in, the Chorus/Expander is active. A footswitch (see #28, rear panel) overrides this switch.
17:CHORUS/EXPANDER: Select between the
18:DEPTH: Set the intensity of the chorus effect with this control: in the far left position there will be almost no cho- rus; as you rotate the control to the right the amount of effect increases.
19:RATE: Set the speed of the chorus effect with this con-
trol: to the left for slow, smooth “phasing” sounds, to the right for faster “vibrato” sounds.
20:POWER LED: Glows when the amplifier is turned on.
21:POWER SWITCH: Turns the amplifier ON in the up position, off in the down position. The POWER LED (#20) works with this switch as a visual indicator.