JVC XV-NP1SL Connecting to a TV with component jacks, Progressive scan video playback available

Preparations

Preparations

CConnecting to a TV with component jacks.

You can enjoy picture of high-fidelity color reproduction by connecting the COMPONENT VIDEO OUT jacks on the player to your TV.

NOTES

•Connect “Y” to “Y,” “PB” to “PB” (CB), “PR” to “PR” (CR) correctly.

•If your TV has component video input jacks of BNC type, use an adapter which converts a pin jack to a BNC jack (not supplied).

Progressive scan video playback available

In the Progressive scanning mode, you can enjoy high quality picture with less flickers when the COMPONENT VIDEO OUT jacks are connected to a TV or monitor that supports the progressive video input.

TV

		IN		PR	Red
				PB
			Y		Blue
S-	VIDEO			EN
			CO	M

VIDEO
LE	FT	White
AUDIO		Green
RIG	HT

Red

MP

ON

EN

T

CO

PR

EO

VID

PB

Red

The player

Y

IA

L

ID

O

UT

COAX

V

LEFT

S-VID

EO

IC

OPT

HT

ITA

L

RIG

T

White

AUD

IO

OU

Green

Blue

Red

Selecting the VIDEO SIGNAL SELECTOR position

•If your television equipped with component jacks does not support the progressive scanning mode

Set the VIDEO SIGNAL SELECTOR to “480i.”

•If your television equipped with component jacks supports the progressive scanning mode

Set the VIDEO SIGNAL SELECTOR to “480p.”

•If you want to select the scanning mode between the interlace and progressive modes (depending on the source condition, or when connecting more than one television, etc.)

Set the VIDEO SIGNAL SELECTOR to “REMOTE.”

Thus you can select the mode from the remote control unit.

NOTE

You must change the VIDEO SIGNAL SELECTOR position while the player power is off. Otherwise, the changed setting is not effective.

Activating the Progressive scanning mode using the remote control unit

When the player is turned on and the VIDEO SIGNAL SELECTOR is set to “REMOTE,” press and hold down VFP - PROGRESSIVE SCAN for a few seconds.

The scanning mode switches between the Progressive scanning and Interlaced scanning modes.

When the scanning mode is set to the Progressive mode, the PROGRESSIVE indicator on the front panel turns on. Depending on the [PICTURE SOURCE] setting on the [PICTURE] preference display (see page 27) and whether the current DVD VIDEO disc is film-source or video-source, the color of the indicator differs, as shown in the table below.

About the scanning mode

Depending on the material source format, DVD VIDEO discs can be classified into two types; film source and video source (note that some DVD VIDEO discs contain both film source and video source). Film sources are recorded as 24-frame-per- second information, while (NTSC) video sources are recorded as 30-frame-per-second (60-field-per-second interlaced) information.

When the player plays back a film source material, uninterlaced progressive output signals are created using the original information. When a video source material is played back, the player interleaves lines between the interlaced lines on each to create the interpolated picture and outputs as the progressive signal.

									VIDEO SIGNAL
									SELECTOR
IDEO		TOR		L				K	REMOTE
		SIG	NA						480p
V	LEC			AV C			LIN
			MOT	E		PU
SE		RE			OM
480p
480i									480i

Component video cable (not supplied)

Audio cable (not supplied)

Setting of	Source type of DVD VIDEO
[PICTURE SOURCE]	Film source	Video source
AUTO	Green	Red
FILM	Green	Green
VIDEO (NORMAL)/	Red	Red
(ACTIVE)

*While stopped in the Progressive scanning mode, the PROGRESSIVE indicator is lit in red regardless of the [PICTURE SOURCE] selection.

NOTES

•The Progressive scanning mode works only when you connect the player’s COMPONENT VIDEO OUT jacks to a progressive TV.

•There are some progressive TV and High-Definition TV sets that are not fully compatible with the player, resulting in the unnatural picture when playing back a DVD VIDEO disc in the Progressive scanning mode. In such a case, use the Interlaced scanning mode. To check the compatibility of your TV set, contact your local JVC customer service center.

•All JVC progressive TV and High-Definition TV sets are fully

compatible with the player (Example: AV-61S902).

4