Connecting to a TV with component jacks, Ntsc

CConnecting to a TV with component jacks

You can enjoy picture of high-fidelity color reproduction by connecting the COMPONENT VIDEO OUT jacks on the player to your TV.

NOTES

•Connect “Y” to “Y,” “PB” to “PB” (CB), “PR” to “PR” (CR) correctly.

•When using the COMPONENT VIDEO OUT jacks, do not connect the S-VIDEO output jack on the player.

•If your TV has component video input jacks of BNC type, use an adapter which converts a pin jack to a BNC jack (not supplied).

Progressive scan video playback available

In the Progressive scanning mode, you can enjoy high quality picture with less flickers when the COMPONENT VIDEO OUT jacks are connected to a TV or monitor that supports the progressive video input.

•The Progressive scanning mode works for the NTSC color system format only.

About the scanning mode

Depending on the material source format, DVD VIDEO discs can be classified into two types; film source and video source (note that some DVD VIDEO discs contain both film source and video source). Film sources are recorded as 24-frame-per- second information, while (NTSC) video sources are recorded as 30-frame-per-second (60-field-per-second interlaced) information.

When the player plays back a film source material, uninterlaced progressive output signals are created using the original information. When a video source material is played back, the player interleaves lines between the interlaced lines on each to create the interpolated picture and outputs as the progressive signal.

The player	Blue

Component video cable (not supplied)

NTSC

525i/p REMOTE

NTSC 525i

PAL 625i

VIDEO SIGNAL

SELECTOR

Audio cable (not supplied)

Selecting the VIDEO SIGNAL SELECTOR position

•If your television accomodates the PAL color system format and does not support the progressive scanning mode:

Set the VIDEO SIGNAL SELECTOR to “PAL 625i.”

•If your television accomodates the NTSC color system format and does not support the progressive scanning mode:

Set the VIDEO SIGNAL SELECTOR to “NTSC 525i.”

•If your television accomodates the NTSC color system format and supports the progressive sanning mode:

Set the VIDEO SIGNAL SELECTOR to “NTSC 525i/p REMOTE.”

Thus you can select the desired scanning mode using the remote control unit.

Activating the Progressive scanning mode using the remote control unit

When the player is turned on and the VIDEO SIGNAL SELECTOR is set to “NTSC 525i/p REMOTE,” press and hold down VFP - I/P for a few seconds.

The scanning mode switches between the Progressive scanning and Interlaced scanning modes.

When the scanning mode is set to the Progressive mode, the [P] indicator lights up in the display window.

Depending on the [PICTURE SOURCE] preference display and whether the current DVD VIDEO disc is film-source or video- source, the indicator that lights up in the display window differs, as shown in the table below.

Green

S-

VIDEO

VID

White

Red

AUD

RIG

Red

TSC

REM

N 525i/p

OTE

PAL

525i

625i

DEO

SIG

VIDEO

ELECTNAL

OMP

ENT

PULI

S-VI

Green

LEFT

IGIT

ALOUT

STRE

IGHT

AUDIO

AXI

Red

Blue

White

Red

Setting of [PICTURE

Source type of DVD VIDEO

SOURCE]

Film source

Video source

AUTO

[DDP]

[P]

FILM

[DDP]

VIDEO (NORMAL)/

[P]

(ACTIVE)

NOTES

•The Progressive scanning mode works only when you connect the player’s COMPONENT VIDEO OUT jacks to your TV.

•There are some progressive TV and High-Definition TV sets that are not fully compatible with the player, resulting in the unnatural picture when playing back a DVD VIDEO disc in the Progressive scanning mode. In such a case, use the Interlaced scanning mode. To check the compatibility of your TV set, contact your local JVC customer service center.

•All JVC progressive TV and High-Definition TV sets are fully compatible with the player (Example: AV-61S902).

•The VIDEO jack, S-VIDEO jack and COMPONENT VIDEO OUT jacks cannot be used at the same time. Connect cable(s)

only to the jack(s) you want to use.

Preparations