JVC 0204KTYBICJSC To adjust the picture character VFP, To dismiss the VFP mode selection window

Page 21

To adjust the picture character (VFP)

The VFP (Video Fine Processor) function allows you to adjust the picture character according to the type of programming, picture tone or personal preferences.

1 During playback, press VFP - PROGRESSIVE SCAN.

The VFP mode selection window appears on the TV screen.

2 Press 2/3 to select the desired preset.

Each time you press the button, the VFP mode changes as follows.

Set the video type most suitable to the current program or the room conditions.

NORMALCINEMAUSER 1USER 2

Selected preset

USER 1

DNR

+ 0

DIGIPURE

+ 0

GAMMA

+ 0

BRIGHTNESS

+ 0

CONTRAST

+ 0

SATURATION

+ 0

TINT

+ 0

SHARPNESS

+ 3

Parameter

[NORMAL]: for watching TV in a general room.

[CINEMA]: for watching a movie software in a room with suppressed light.

[USER 1] [USER 2]: you can adjust parameters that affect the picture character and store the settings as a user preset. See the next step.

3 To define a user setting, press 5/∞ to select a parameter to be edited from the following.

•DNR (Digital Noise Reduction)

Adjust this if you notice “mosquito noise” (noise that randomly appears along the edges of digitally compressed pictures).

Available range: 0 to +1.

•DIGIPURE

Adjust this if you want to enhance clarity of pictures. Available range: 0 to +3.

•GAMMA

Adjust this if the neutral color is bright or dark. The brightness of dark and bright portion is maintained. Available range: –4 (darkest) to +4 (brightest).

•BRIGHTNESS

Adjust this if the picture is bright or dark on the whole. Available range: –16 (darkest) to +16 (brightest).

•CONTRAST

Adjust this if the far and near position is unnatural. Available range: –16 to +16.

•SATURATION

Adjust this if the picture is whitish or blackish. Available range: –16 (blackest) to +16 (whitest).

•TINT

Adjust this if the appearance of flesh tone is unnatural. Available range: –16 to +16.

•SHARPNESS

Adjust this if the picture is indistinct. Available range: 0 to +3.

4 Press ENTER.

A window for setting parameters appears.

SATURATION

+ 4

Selected parameter

5 Press 5/∞ to adjust the level of the parameter.

The higher value enhances the effect.

6 Press ENTER.

Repeat steps 3 to 6 if you want to set other parameters.

To dismiss the VFP mode selection window

Press VFP - PROGRESSIVE SCAN.

NOTE

The window for VFP mode selection and parameter setting disappear if no operation is made for about 10 seconds.

To simulate surround sound (3D PHONIC)

Using the 3D PHONIC function, you can get a simulated surround effect from your stereo system.

1 During playback, press 3D PHONIC.

The 3D PHONIC window appears on the TV screen.

2 Press 2/3 to select the desired mode.

Each time you press the button, the 3D PHONIC mode changes as follows:

ACTIONDRAMA THEATERNONE

ACTION +45

Selected effect mode

•ACTION

Suitable for action movies and sports programs in which the sound source moves.

•DRAMA

Natural and warm sound. You can enjoy movies in a relaxed mood.

•THEATER

You can enjoy sound effects like in a theater.

3 Press 5/∞ to adjust the effect level.

You can set the effect level from [1] to [5].

The higher value enhances the effect.

To dismiss the 3D PHONIC window

Press 3D PHONIC.

NOTES

•The 3D PHONIC window disappears if no operation is made for about 10 seconds.

•The 3D PHONIC function works correctly only when playing back a DVD VIDEO disc recorded with Dolby Digital.

•When playing back a DVD VIDEO disc recorded with Dolby Digital that does not contain the rear signal, you can change the 3D PHONIC setting, but you will not be able to achieve a correct 3D effect.

•The 3D PHONIC function does not affect the Dolby Digital bitstream signal from the DIGITAL OUT jack.

•When the 3D PHONIC function is active, the [ANALOG DOWN MIX] setting in the [AUDIO] setting display is not available.

Various kinds of playback

19

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Changing the initial settings Region code of DVD VideoPlayer’s region code is printed on the rear of the player Important for Laser Products Table of contents Supplied accessoriesPrecautions About this manualAbout discs Before operationDisplay window Remote control unit Names of parts and controlsFront panel Setting the selector Connecting to a TVConnections Before making connectionsConnecting to a TV with an S-video jack Connecting to a TV having composite video input jackWhite RedConnecting to a TV with component jacks Progressive scan video playback availableSource Connecting to a stereo audio amplifier/receiver Connecting to optional audio equipmentPlayer Red Audio cable not suppliedDigital equipment Connecting to a digital audio deviceConnecting the power cord Using the remote control unitTo install batteries Precautions of the safe use of batteriesInitial setup Basic playbackTurning the player on and off Starting playback Changing the resume mode Restarting playback after stopping resuming playbackAbout On-screen guide icons Playback at various speeds Various kinds of playbackLocating the beginning of a scene or song Using the numeric buttonsPlaying from a specific position Locating a desired scene from the DVD menuSpecifying a desired title/group Changing the playback orderTo play back in a specific order Program play About PBC Playback ControlTo play back in random order Random play To exit the program modeTo stop program playback To clear the programChanging the language, sound and scene angle Repeat playbackTo repeat a desired part A-B repeat playback To select the subtitle language SubtitleTo change the audio language or sound Audio Special picture and sound effectsTo select a scene angle of DVD Video Angle To zoom in picturesTo adjust the picture character VFP To dismiss the VFP mode selection windowTo dismiss the 3D Phonic window Menu bar functions Basic operation procedureTo bring up the menu bar To dismiss the menu bar and status barMenu bar functions for DVD Video Time mode selectionMenu bar functions for SVCD/Video CD/ Audio CD CHAP. Chapter searchOperations MP3/WMA disc playbackAbout MP3/WMA discs Basic operationsDirect selection Repeat playbackDuring playback or while stopped, press Press the numeric buttons to specify a desired group numberAbout Jpeg discs Jpeg disc playbackBasic operations To see a desired pictureTo zoom in the picture Viewing pictures continuously slide show modeTo start the slide show Repeat functionHow to set preferences Changing the initial settingsSelecting preferences About the Preference displayPicture menu Language menuENGLISH, FRENCH, German ON, OFFOthers menu Audio menuTo set Parental Lock for the first time Limiting playback by childrenStop mode, bring up the Others menu Press 5/∞ to move To select Parental Lock then press EnterTo temporarily release the Parental Lock To change the settingsAdditional information TroubleshootingSpecifications For Appendix a Country/Area code list for Parental LockOutput Disc type Appendix C Digital output signal chartAppendix D Glossary Victor Company of JAPAN, Limited Above ALL
Top Page Image Contents