Hitachi L40A105 important safety instructions TV operation, To select the video input source

Page 13
Scan
Start
Source
Cable
TV Location
Store
Starting setup
The Auto Setup menu appears the first time you turn on the TV, and assists you to specify the Air/Cable setting, and program your channels automatically.
IMPORTANT: Make sure that the antenna or cable TV system connection is made!
1 To turn on the TV, press POWER (POWER indicator on the front of the unit changes green. It may take approx. 10 seconds for a picture to appear on screen.). The Auto Setup function begins.
Auto Setup

 

Press ▲ or ▼ to select “TV Location”, then press or to

2 select “Home” or “Store”. This product qualifies for ENERGY

 

STAR In Home mode default setting.

 

NOTE:

 

• This unit has been preset to STORE brightness. This setting

 

does not qualify under ENERGY STAR. To reduce brightness

 

and energy consumption, change setting to ‘HOME’. This

 

setting does qualify under ENERGY STAR.

 

• The device may not conform to the ENERGY STAR standard

3

after Reset is performed or the Backlight is adjusted.

Press ▲ or ▼ to select “Source”, then press or to select

“Air” or “Cable”.

4

Press ▲ or ▼ to select “Scan”, then press or ENTER.

5

“Auto Setup” will begin. After the Auto Setup is completed, the

TV channel appears on the screen.

 

• Depending on the reception condition, it may take up to 30

 

minutes to complete memorizing digital cable channels.

 

Please allow the process to complete without interruption.

NOTE:

• If you press EXIT in the process of “Auto Setup”, the Auto Setup stops and changes to the normal screen.

• When you make a menu selection, your changes occur immediately.You do not have to press EXIT to see your changes.

TV operation

1 To turn on the TV, touch POWER.

(POWER indicator on the front of the unit changes green. It may take approx. 10 seconds for a picture to appear on screen.)

2 Adjust the volume level by pressing VOL + or . The volume level will be indicated on the screen by green bars. As the volume level increases, so do the number of bars. If the volume decreases, the number of green bars also decreases.

3 Set the Source option to the appropriate position (see “Air/ Cable selection” on page 16).

4 Press the Direct Channel Selection Buttons (0-9) buttons to select the channel.

(If you press only the channel number, channel selection will be delayed for a few seconds.)

TO SELECT ANALOG CHANNELS

1-9: Press 1-9 as needed. Example, to select channel 2, press 2, then press ENTER.

10-99: Press the 2 digits in order. Example, to select channel 12, press 1, 2, then press ENTER.

100-135: Press the 3 digits in order. Example, to select channel 120, press 1, 2, 0, then press ENTER.

TO SELECT DIGITAL CHANNELS

Press the first 1-3 digits, then press the button followed by the remaining number.

Example, to select channel 15-1, press 1, 5, , 1, then press

ENTER.

• If a channel is selected with only audio content, “Audio only” will be displayed on the screen.

• If a channel is selected with a weak digital signal, “Weak Signal or Channel not available.” will be displayed on the screen.

• The same program may be available on either an analog channel or a digital channel.You may choose to watch either format.

• If a channel is selected to which you have not subscribed, “Digital channel is encrypted” will be displayed on the screen.

VHF/UHF/CABLE CHANNELS

Air

 

Cable

VHF

 

VHF

2-13

 

2-13

UHF

STD/HRC/IRC

14-69

14-36

(A) (W)

 

37-59

(AA) (WW)

 

60-85

(AAA) (ZZZ)

 

86-94

(86) (94)

 

95-99

(A-5) (A-1)

 

100-135 (100) (135)

 

01

(4A)

NOTE:

• If a channel with no broadcast is selected, the sound will automatically be muted.

• It may take a few seconds for a digital channel picture to appear on screen after being selected.

To select the video input source

To view a signal from another device connected to your LCD TV, such as a VCR player, press INPUT, then press ▲ or ▼ or corresponding Number buttons (0-7), then press ENTER.You can select TV, Video1, Video2, Component, HDMI1, HDMI2, HDMI3 or PC depending on which input jacks you used to connect your devices.

Input List

0.TV

1.Video1

2.Video2

3.Component

4.HDMI1

5.HDMI2

6.HDMI3

7.PC

[0-7]:Select

CH /

Press and release CH /. The channel automatically stops at the next channel set into memory.

For proper operation, before selecting channels, they should be set into the memory. See “Memorizing channels” on page 16.

ENGLISH

13

Image 13
Contents Owners Guide Energy Star Location of the required MarkingLead/Mercury Notice Important Safety Instructions HOW to Handle the LCD Panel Power sourceDeclaration of Conformity CondensationChild Safety Notice Securing to a Wall Safety PrecautionsHow to remove the stand How to attach the standPower source FeaturesTo USE AC Power Before using your unit ContentsFront Left side Location of controlsRear CH ChannelBattery Precautions Remote controlCH Channel / Buttons Press to change Cable TV connections Antenna connectionsTo select the video input source TV operationExample Select Menu Language Quick guide for menu operationConvenience functions Icon Selected Items Setup hintMemorizing channels Setting the Parental Control Checking the digital signal strengthLabeling channels Labeling video inputsTo set the Parental Control To change the passwordDownloading the additional Parental Control rating system Closed Caption Aspect SwitchingCC advanced Opacity FlashingNatural Native for PC mode onlyCinema Wide1 for 43 format programs Cinema Wide2 for letter box programsTo connect the LCD TV to a VCR Connections to other equipmentTo connect the LCD TV to a camcorder, or a game console VCRTo connect an audio system Using an AV Amplifier with built-in digital surroundTo connect a Hdmi or a DVI device to the unit To return to normal modeTo connect the TV to a PC Personal Computer Rear and Left of the unitReception disturbances Symptoms Possible Solutions TroubleshootingAccessories SpecificationsGeneral TelevisionOrion SALES, INC Limited Warranty