Hitachi L32C205 important safety instructions Starting setup

Starting setup

will assist you to specify the Air/Cable setting and program your channels automatically.

IMPORTANT: Make sure that the antenna or cable TV system connection is made.

1To turn on the TV, touch POWER (POWER indicator on the front of the unit changes blue. It may take approx. 10 seconds for a picture to appear on screen.). The Setup Wizard function begins.

Setup Wizard	Tuner
Please select your tuner mode:	Air
	Cable

Move SEL Select Return

2 Press ▲ or ▼ to select “Source”, then press ￿ or ￿ to select



“Cable” or “Air”.

3Press ▲ or ▼ to select “Scan”, then press ￿ or SELECT.

4“Setup Wizard” will begin. After the Setup Wizard is completed, the TV channel appears on the screen.

•Depending on the reception condition, it may take up to 25 minutes or more to complete memorizing digital cable channels. Please allow the process to complete without interruption.

NOTE

•If you press EXIT in the process of “Setup Wizard”, the Setup Wizard stops and changes to the normal screen. When you make a menu selection, your changes occur immediately. You do not have to press EXIT to see your changes.

TV operation

1To turn on the TV, press POWER.

(POWER indicator on the front of the unit changes blue. It may take approx. 10 seconds for a picture to appear on screen.)

2Adjust the volume level by pressing VOL or . The volume level will be indicated on the screen by volume bars. As the volume level increases, so do the number of bars.

If the volume decreases, the number of volume bars also decreases.

3Set the Source option to the appropriate position.

4Press the Direct Channel Selection (0-9, –) buttons to select the channel.

(If you press only the channel number, channel selection will be delayed for a few seconds.)

TO SELECT ANALOG CHANNELS

1-9: Press 1-9 as needed. Example, to select channel 2, press 2, then press SELECT .

10-99: Press the 2 digits in order. Example, to select channel 12, press 1, 2, then press SELECT.

100-135: Press the 3 digits in order. Example, to select channel 120, press 1, 2, 0, then press SELECT.

TO SELECT DIGITAL CHANNELS

– button followed by

the remaining number.

Example, to select channel 15-1, press 1, 5, –, 1, then press

SELECT.

•If a channel is selected with only audio content, “Audio only” will be displayed on the screen.

•If a channel is selected with a weak digital signal, “Weak Signal or Channel not available.” will be displayed on the screen.

•The same program may be available on either an analog channel or a digital channel. You may choose to watch either format.

•If a channel is selected to which you have not subscribed, “Scrambled ” will be displayed on the screen.

VHF/UHF/CABLE CHANNELS

Air	Cable
VHF	VHF
2-13	2-13
UHF	CATV 1-125
14-69	Digital Terrestrial Broadcast(8VSB):2-69
	Digital cable(64/256 QAM):1-135

NOTES

•If a channel with no broadcast is selected, the sound will automatically be muted.

•It may take a few seconds for a digital channel picture to appear on screen after being selected.

To select the video input source

To view a signal from another device connected to your LCD TV, such as a VCR player, press INPUT, then press ▲ or ▼, then press SELECT.You can select TV, Video, Component, HDMI or

RGB depending on which input jacks you used to connect your devices.

Input

TV

AV

Component

RGB

HDMI 1

HDMI 2

SEL Select Move MENU Return



CH /

Press and release CH /. The channel automatically stops at the next channel set into memory.

For proper operation, before selecting channels, they should be set into the memory. Refer to the Channels Menu on page 14.

ENGLISH