Polaroid FLM-323B manual Chapter Programming your Remote Control

Page 46

Chapter 4

Programming your Remote Control

Introduction

Your remote lets you control four devices with one easy-to-use, compact unit. After installing batteries, you can program the remote to control your Universal TV, VCR or DVD, Cable or Satellite Receivers, Amplifier or Tuner, and Auxiliary devices. To do so, follow the instructions in “Programming a Device”. For best results, please read and follow all the remaining instructions. Keep this guide for future reference.

A Quick Look at Programming a Device

To control VCR or DVD, Cable or Satellite Receivers, Amplifier or Tuner, and Auxiliary devices, follow these steps. Before proceeding, find the codes for the devices you want to program in “Manufacturer’s Codes” on the right side of this page and write them down or highlight them.

NOTE: To program a DVD Player, TV/DVD Combo, TV/VCR/DVD Combo, portable DVD player, or mobile DVD player, use the DVD key.

1.Turn on the device (for example, DVD player) and, if needed, load media (for example, a DVD).

2.Press a device key (VCR/DVD, CBL/ SAT, or AUX).

3.Press and hold SET until the red LED blinks twice; then release.

4.Enter the first five-digit code for your device. The LED blinks once as each digit is entered. If the code is correct, the LED blinks twice.

NOTE: If the LED does not blink twice, repeat steps 2 to 4 and try entering the code again.

5.Aim the remote at the device and press Power. The device should turn off. If it does not, repeat steps 3–5, trying each code for your brand until you find one that works. If you cannot find a code that works, see “Searching for Your Code”.

6.Repeat steps 1–5 for the other devices you want to control. For future reference, write down each working device code below:

AUX Code: CBL Code: CD Code:

DVD Code: SAT Code: TNR Code: VCR Code:

7.Press set to save and exit

Searching for your Code

If your device does not respond to the remote after trying all codes listed for your brand, or if your brand is not listed, try searching for your code:

1.Press a device key once.

2.Press and hold SET until the red LED blinks twice; then release.

3.Enter 9-9-1, then the device group number (0= Cable, 1= TV, 2= VCR, 3= Audio). The LED blinks twice.

4.Aim the remote at the device and press Power. The remote sends IR codes from its library to the selected device, starting with the most popular code first. If the device responds, go to step 7.

5.If the device does not respond, press CH+. The remote will try the next code. Continue until the device responds.

Note: Press CH- to try the previous code.

6.To search for other device codes, repeat steps 1 to 5.

7.Press SET to save and exit.

Checking the Codes

If you have set up the remote using the procedure in “Searching for Your Code”, you may need to find out which four-digit code is operating your equipment.

For example, to find out which code is assigned to your TV:

1.Press TV once.

A

Image 46
Contents LCD Television with NTSC/ATSC Tuner Federal Communications Commission Statement Important Safety Instructions English Outdoor Antenna Safety Instructions Ground clampsTable of Contents Key Features Chapter Introducing the LCD TVPackage Contents Setting Up Your LCD TV Attach the Stand Connect other an external A/V device refer to page14-26 Your LCD TV Front/Right Side View and ControlsVideo VIDEO2Hdmi VGAYour Remote Control SETInfo Effective rangeType connector Ohm coaxial cable round Connecting a TV Cable or an AntennaOhm twin-lead cable flat Combination VHF/UHF antenna Splitter Cable TV Line VHF/UHFPress the button on the remote to turn on the LCD TV Method a Method a Connecting a VCRMethod B Connecting a Video Camera or Play Station Rear of TV Right SideConnecting a DVD Player Method CEnglish COMPONENT/AUDIO Cable Connecting an AV Equipment with Hdmi Connector Connecting an AV Equipment with DVI Connector Connecting a PC Connecting to Audio Receiver Connecting to Digital 5.1 Sound SystemPress to change input source and press the OK button Using Picture-In-PictureMain  Press the PIP button again to view images side by side Wide Screen Viewing Displays at 43 aspect ratioVideo Menu Operating the MenuAudio Menu TV Menu Setup MenuHdtv Menu Setting up the Hdtv Function  The Hdtv menu includes the following options Using the Program Guide Customizing the Video Settings  The Video menu includes the following options The Audio menu includes the following options Customizing the Audio SettingsSAP Customizing the Setup Settings  The Setup menu includes the following optionsCC1 /CC2 /CC3 /CC4 DefaultClosed Caption T1/T2General Audiences. Movie is appropriate for all ages Using the V-CHIP SettingsRating Description Viewers The V-CHIPmenu includes the following options  The Parental menu includes the following options Using the Parental SettingsChange Password Selects to change your password Channel Lock Selects to block a TV channel Video LockAntenna Customizing the TV Settings The TV menu includes the following options Cable STD/CABLE IRC/CABLE HRCSpecifications FLM-3732/FLM-373B Chapter Programming your Remote Control Unlocking All Volume Control Restoring Global Unlock Locking Volume Control to One Mode Global Volume LockUnlocking a Single Device’s Volume Control Set Codes for Audio Amplifiers Set Codes for Audio Amp/TunersABC Set Codes for Cable ConvertersSet Codes for CD Players KNCSet Codes for DVD Players SVA Set Codes for Satellite Receivers Set Codes for TVsCXC KTV JCBKEC LXITMK Set Codes for VCRsSSS TVSCCE ABSHI-Q MEI STSCare