Magnavox MS1940B warranty Setting UP and Using Your TV CONT’D, Remote, Television, Channel Edit

REMOTE

SETTING UP AND USING YOUR TV (CONT’D)

T o load the batteries into the remote:

1.Press in the tab on the battery compartment lid on the bottom of the remote control, then lift off the lid.

2.Insert two AA batter- ies (supplied) into the battery compartment as indicated inside the compartment. Installing batteries incorrectly may damage the remote control.

3.Replace the lid.

Battery

Compartment

Lid

Battery

Compartment

Point the remote control toward

the remote sensor on the TV when operating the TV with the remote. (See Television illustration below.)

SLEEP Button

Press to set the TV to turn itself OFF auto- matically. Details are on page 5.

Number Buttons

Press to select channels.

•Cable Users

Enter channel numbers as a two-digit num- ber for the quickest results. For example, to select channel 6, press 0,6. If you only press the Number 6 button, channel 6 will be selected after a brief delay. (There also may be a brief delay when you select channels 10, 11, and 12.) If you want to select channels 100 and above, enter channel numbers as a three-digit number. For example, to select channel 117, press 1, 1, 7.

•Antenna Users

Enter channel numbers as a two-digit num- ber for the quickest results. For example, to select channel 5, press 0,5. If you only press the Number 5 button, channel 5 will be selected after a brief delay. You may only select channels 2-69.

STATUS/EXIT Button

Press to see the current channel number on the TV screen. Press to remove the on- screen menu. You also may remove the menu by pressing the CH(annel) ▲/▼ but- tons to select EXIT, then pressing the VOL(ume) B/{ buttons. (You may need to select EXIT repeatedly to completely remove all of the menus.)

POWER Button

Press to turn the TV ON and OFF.

SLEEP

POWER

			ALT. CH (Alternate Channel) Button
			Press to return to the TV channel you were view-
			ing immediately before switching to your current
1	2	3
			channel.
4	5	6	MENU Button
			Press to access or remove the on-screen menu.
7	8	9	Press the CH(annel) ▲/▼ buttons to select an
			item in the menu. Press the VOL(ume) B/{ but-
STATUS/EXIT		ALT.CH	tons to adjust an item in the menu or to advance
	0
			to the next menu.
MENU			MUTE Button
		MUTE
	CH.		Press to turn OFF the sound on the TV. Press
			again to restore the sound.

VOL.		VOL.
		VOL(ume) B/{ Buttons
	CH.	Press to adjust the TV sound level. Press to adjust
		an item in the on-screen menu or to advance to
		the next menu.
		If you press the VOL(ume) { button when the
TV/AUX	CC	sound is muted, the volume indicator will appear
		on the screen. Pressing the VOL(ume) B button
		when the sound is muted will restore the sound.
		CH(annel) ▲/▼ Buttons
		Press to scan through available channels. Details
		are on page 3. Press to select an item in the on-
		screen menu.
		CC (Closed Caption) Button
		Press repeatedly to select a Closed Caption
		mode. Details are on page 7.
		TV/AUX Button
		Press to select A/V IN (for viewing video playback
		at the TV from a VCR, camcorder, DVD Player,
		etc.). Press again to return to another TV channel.
		Details are on page 3.

TELEVISION

SMART

Press the POWER button to turn ON the TV. Be sure to connect the TV power cord to a standard AC outlet first.

Press the VOLUME

▲/▼ buttons to adjust the sound level.

Press the CHAN- NEL ▲/▼ buttons to select available TV chan- nels.

(See Auto Install on page 3.)

Press the MENU button

to display the TV’s on-screen menu.

Press the CHANNEL ▲/▼ buttons to select an item in the menu.

Press the VOLUME ▲/▼ but- tons to adjust an item in the menu or to advance to the next menu.

HELP

The current channel number will appear briefly when the TV is first turned ON and with channel changes. To display the channel number for five seconds, press the

STATUS/EXIT

Remote Sensor

Point the remote control here when using the remote to work the TV.

VIDEO L - AUDIO - R HEADPHONE MENU VOLUME CHANNEL POWER

Note:

•You can connect headphones (not supplied) to the HEADPHONE jack on the front of the TV for private, personal listening.

•You can connect the AUDIO/VIDEO In jacks on the front of the TV to the AUDIO/VIDEO OUT jacks of a camcorder, VCR, or other video equipment. Details are on page 3.

Note: To remove the menu, press the CHANNEL ▲/▼ but- tons to select EXIT. Then, press the VOLUME ▲ or ▼ button. (You may need to select EXIT repeatedly to completely remove all of the menus.)

Or, press the MENU button, repeatedly if necessary, to remove the MENU.

button.

You can turn on the TV by pressing the CHANNEL ▲/▼ but- tons on the front of the TV. The CH(annel) ▲/▼ but- tons of the remote control will not turn on the TV power.

FEATURES

CHANNEL EDIT

AUTO INSTALL (see page 3) memorizes all the channels on

your Antenna or Cable TV system. CHANNEL EDIT makes it easy for you to add other channels or drop unwanted channels from the TV’s memory. Then, when you use the CH(annel) o/p buttons, you will only scan through the channels you want.

Press the MENU but- ton, then press the CH(annel) ▲/▼ buttons to select SETUP.

SmartLock	B
SmartLock REVIEW	B
SETUP	B
EXIT	B
BRIGHTNESS	24

Press the VOL(ume)

Bor { button to continue to the SETUP menu.

EXIT	B
LANGUAGE	ENG
AUTO INSTALL	B
CHANNEL EDIT	B

Press the CH(annel)

Press the VOL(ume)

Bor { button to continue to the CHANNEL EDIT menu.

CHANNEL will be selected.

EXITB

CHANNEL10

SKIPPEDYES

Press the CH(annel)

▲/▼ buttons to select

SKIPPED.

Then, press the VOL(ume)

B or { button to set

SKIPPED to YES (if you want

to skip past the channel when

using the CH(annel) ▲/▼ but-

tons) or NO (if you want the

channel to be available when

1 2 3

4 5 6

7 8 9

STATUS/EXITALT.CH

▲/▼ buttons to select

CHANNEL EDIT.

AUTO INSTALL	B
CHANNEL EDIT	B
EXIT	B
LANGUAGE	ENG

While CHANNEL is selected, press the VOL(ume) B or { button or the Number buttons to select the channel you

you are using the CH(annel)

▲/▼ buttons).

CHANNEL18

SKIPPEDNO

EXITB

	0
MENU	MUTE
	CH.
VOL.	VOL.
	_
	CH.

want to add or skip.

EXITB

CHANNEL18

SKIPPEDYES

Press the STATUS/EXIT button

when you are finished.

- 4 -