CONNECTION
Terminal Positions
SD MEMORY
CARD h
| P |
|
|
|
|
|
|
|
|
| P |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| w |
|
|
| OK |
|
|
|
|
|
| INPUT(RGB) |
|
|
|
|
|
|
| ANT |
| AUDIO |
|
|
|
|
|
|
|
|
|
| |
| ertyu |
|
| ANALOG RGB | a | ||||
|
|
|
|
|
|
|
| PC |
|
|
|
|
|
|
|
|
| INPUT(HDMI) |
|
| INPUT INPUT INPUT INPUT | OUTPUT |
|
| AUDIO |
| |||
| (AV1) | (AV2) | (AV3) | (AV4) | WOW, SRS and | symbol are trademarks of SRS Labs, Inc. |
|
| |
| Y/VIDEO | Y/VIDEO |
|
|
|
|
|
|
|
|
|
|
|
|
| Licensed by BBE Sound, Inc. under USP5510752 and 5736897. |
|
| |
|
|
|
|
|
| BBE and BBE symbol are registered trademarks of BBE Sound, Inc. |
|
| |
|
|
|
|
| SUB |
| i | HDMI2 | s |
| P | P |
|
| WOOFER |
| |||
| P | P |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| HDMI1 |
|
PH35814 | AUDIO | AUDIO | AUDIO | AUDIO | AUDIO | SERVICE USE ONLY |
|
| |
| L | L | L | L | L |
|
| o |
|
| C | C | C | C |
|
|
|
|
|
| R | R | R | R | R |
|
|
|
|
|
|
|
|
|
| POWER SWIVEL |
|
| |
| A C |
|
|
|
|
|
|
| |
q
Connecting Procedure
PH35826
|
| |
INPUT(AV5) | L/MONO | AUDIO VIDEO |
| R |
|
Rear
qPower Cord Socket
g w Aerial Socket
e AV1
fr AV2 t AV3 y AV4
u Monitor Out and Sub Woofer i Service use only
oPower Swivel Terminal
d(see 36 )
aPC Connection terminals
sHDMI1, 2 and mini stereo for Audio
Side
dAV5
fHeadphone input
gPhoto Input terminal
hSD Memory Card slot
This unit is ready for various kinds of connections. Make a connection in the following steps. Be sure to turn off the Main Power fi rst when connecting external equipments.
1.Connect Power Cord to the rear panel.
2.Connect Aerial Lead.
3.Connect your external equipments to the unit if any.
4.Connect the Power Plug to the Wall Socket.
1. Connecting Power Cord to the Rear Panel
Connect Power Cord to the monitor.
*Make sure not to connect the Power Plug to the Wall Socket until all connections are completed.
2. Connecting Aerial Lead.
There are two ways to connect Aerial Lead.
qWhen you do not have any other external equipment:
Connect the Aerial Lead directly into the Socket at rear panel.
wWhen you have one or more external devices to connect:
STB VCR
IN | IN |
OUT | OUT |
1. Use RF cable to connect between each equipment and Antenna.
2.Connect the Aerial Lead to an equipment‘In’Socket marked
3.Connect the RF cable from the equipment ‘Out’ to the other equipment ‘In.’
4. Then, connect from the equipment ‘Out’ to “ANT” on the plasma screen Socket on marked .
Precautions when connecting the aerial
Please use a coaxial cable which is free from interference to connect the aerial. Avoid using a parallel fl at feeder wire as interference may occur, causing reception to be unstable and stripe noise to appear on the screen.
Avoid using indoor aerial as this may be affected by interference. Please use CATV net or outdoor aerial.
For safety, install an external aerial conforming to AS1417.1 (applicable for Australia only)
If there are noise appearance in the picture of
13