Magnavox 37MF321D user manual Select the menu language, Store TV channels

Page 13

Installation

 

 

Settings

Installation

TV

Language

Setup

Autoprogram

Installation

Weak channel installation

Exit

Software upgrade

 

 

Info

 

 

 

 

 

Settings

 

Installation

Autoprogram

Language

 

Autoprogram

Start now

Weak channel installation

 

Software upgrade

 

Info

Television Installation

Installation mode

Antenna

Please select your

Cable

installation mode

 

 

Previous

Next

Select the menu language

1

Press the MENU button on the remote control.

2Use the cursor down to select Installation in the Settings menu.

3 Use the cursor right to enter the Installation menu.

4 Select Language and enter the list of available languages with the cursor right.

5 Select your preferred language with the cursor up/down and press the OK button to confirm you selection.

6 Proceed with the Installation menu.

Store TV channels

1

Select Autoprogram in the Installation menu.

2Use the cursor right to enter the Autoprogram menu.

3 Press the OK button.

4 Select Cable or Antenna in the Installation mode. When Antenna is selected, the TV will detect antenna

signals and will search for antenna TV (NTSC and ATSC) channels available in your local area.

When Cable is selected, the TV will detect cable company supplied signal sand will search for cable TV (NTSC, ATSC, QAM modulated) channels available in your area.

Make sure that registration with your cable TV provider and connection of equipment are completed.

5 Press the green button “Next” on the remote control.

Note: All channels must be unlocked in order to autoprogram. If requested, enter your PIN code to unlock all channels. See Menu preferences in the Settings, TV menu, p. 17.

6Press the green button “Start” to start autoprogramming. The menu screen disappears and the progress of autoprogramming is displayed. The progress bar indicates the number of analog and digital TV channels found.

When Autoprogramming is complete, a message appears confirming the completion and the TV switches to the first

installed TV channel.

Notes:

When you have locked TV channels before initiating Autoprogram, a message appears asking to enter your PIN code in order to complete Autoprogramming.

ATSC channel information is updated automatically when the TV is in standby after 3 minutes and every 3 hours thereafter.

When channel update is interrupted, the new updated channel information is retained along with the old un-updated channel information.

Background Autoprogramming occurs only when the TV is turned on.

Channel information about an ATSC channel is updated only for the ATSC channel currently tuned.

If an NTSC channel is tuned, then in Background Autoprogramming the TV shall scan all the possible ATSC frequencies and update information.

Weak channel installation allows you to manually tune weak ATSC channels in order to adjust the antenna and thus optimize signal quality for that channel. (See Installation menu, Weak channel installation, p. 14.)

Once you have searched for the available Antenna as well as the Cable TV channels, they are stored in the memory.

If Antenna/cable signal is interrupted more than ten minutes, TV will go into off mode. You are requested to press Power button or CH / button to turn on the TV.

13

Image 13
Contents LCD TV For Customer Use Proof of PurchaseRead before operating equipment Important Safety InstructionsAdditional Safety Precautions PrecautionSetup menu Introduction InstallationConnect accessory devices Trouble shooting tips Care and cleaningMounting the TV on the wall PreparationBasic connections to the TV Cable box with RF IN/OUT Cable TVCable box with A/V outputs Antenna Remote controlDirect Broadcast Satellite DBS Turn the TV onUse of the remote control Format Buttons on the top of theTV To use the menus Introduction How to navigate through the Settings menusStore TV channels Select the menu languageWeak channel installation Channel tuningSoftware upgrade USB upgradeSelect Captions service Features preferences Caption servicePreferences Auto surroundReset to default Digital caption serviceDigital caption options SizeShow emergency alerts EAS Menu preferencesSet/Change PIN Source Reset AV settingsAnalog Audio Digital Audio OutClock Auto clock modeSmart picture Picture menuContrast BrightnessSharpness Color temperatureTint Picture formatSound menu Sleeptimer Features menuSelect Sleeptimer Closed captionsLock after Channels menuChannel lock TV ratings lockTV-Y Preferred channels Movie Ratings LockClear region ratings Region ratings lockIf your recorder has an S-VHS video jack Recorder VCR-DVD+RWRecorder and cable box with RF output Recorder and other A/V devicesSatellite Receiver / cable box with AV outputs Video or Audio L and R, and to AV2 Video or Audio L and RDigital Surround receiver Recorder and Satellite Receiver / cable box with AV outputsCursor keys Devices with an S-Video connectorSide connections Camera, Camcorder, Game Hdmi High Definition Multimedia Interface connectorsHeadphone Record a TV program RecorderNo power Trouble ShootingTipsTV Location CleaningVerifying the version of the TV software Automatic software upgrade procedure Magnavox Limitedwarranty