Fujitsu ZCAT1518-0730, SFT-72SN user manual Selecting Input Mode, Press to select the input mode

Page 28

SELECTING INPUT MODE

VIDEO INPUT MODE (for the W/R models)

1	Press to select the input mode.
	Press to select the input mode.
	You can select from VIDEO1 mode to VIDEO4
	mode.
	The video modes corresponding to each input
	terminal are as follows.
	• VIDEO1: Video
	• VIDEO2: S-video
	• VIDEO2: S-video	Video1 mode
	• VIDEO3: Component video	Video1 mode
	• VIDEO3: Component video
	• VIDEO4: Component video
	* For selection of the input terminal, see
	“SETTING THE INPUT TERMINALS” on
	P. E-31.

*You can also use the buttons on the display’s control panel to perform these steps.

VIDEO INPUT MODE (for the U model)

1	Press to select the input mode.
	Press to select the input mode.
	You can select from VIDEO1 mode to VIDEO5
	mode.
	The video modes corresponding to each input
	terminal are as follows.
	• VIDEO1: Video
	• VIDEO2: S-video
	• VIDEO2: S-video	Video1 mode
	• VIDEO3: Component video	Video1 mode
	• VIDEO3: Component video
	• VIDEO4: Component video
	• VIDEO5: HDMI
	* For selection of the input terminal, see
	“SETTING THE INPUT TERMINALS” on
	P. E-31.

*You can also use the buttons on the display’s control panel to perform these steps.

DownloadedE-14FromTV-Manual.com Manuals

Image 28

Contents Specification and Part Names ContentsChecking Accessories Connecting the Display to External EquipmentFerrite cores Two big ferrite coresDisplay Section Front Side InstallationReference Part Names and Functions Display Section FrontBack Bottom  / I power switch Display Section Back and Bottom Part Hdmi input terminal VIDEO5 INPUT/HDMI for the U model  RS-232C terminal RS-232C Power input terminal  Video input terminal VIDEO1 Input S-Video input terminal VIDEO2 Input  External speaker output terminal EXT SPPin No Input signal Pin No SignalDescription of Input Terminals Hdmi High-Definition Multimedia Interface Options EnglishMain corresponding signals RGB mode Display dots x lines Main Supported SignalsVertical frequency Hz Signal Hdmi Frequency kHz Frequency HzModel SpecificationRegulation P42VHA40U P42HHA40U P50XHA40U P55XHA40U P63XHA40U Specification Precautions and Adjustment Methods Information Using the Remote Control &Video input mode selector button Î E-14 *RGB input mode selector button Î E-15 12Volume adjustment buttons Î E-13 CDEFAdjustment buttons Î E-19-E-35Putting Batteries in the Remote Control PrecautionsEffective Range for the Remote Control Upper Lower Left Right FrontExample of Connection to External Components VCR or other external components See P. ÎVCR Display bottomDVD RECORDER/PLAYER Çais EspañolSatellite Tuner Póññêèé Português Italiano Français Español Deutsch English Turning the Power on and STAND-BY Press on the remote controlPress when the power is on Basic OperationsAdjusting the volume Adjusting the VolumeMuting the audio Selecting Input Mode Press to select the input modeRGB Input Mode Press to select the input modePicture Mode Other Basic OperationsConvenient Functions On-screen informationSwitching Between Screen Sizes Watching Pictures on the Wide ScreenPress Press to select a desired Screen SizeScreen Size Aspect RatioAdjustment Menu MenuPress to store Press when you finish PressPress Eor Fto select Picture Press Cor Dto select TintAdjusting the Picture Precision Setting for the U model Setting Picture ModeSetting Picture Memory Adjusting the Black Level Setting Detail GradationSetting 3D NR Setting Codec NRSetting Image Enhance Adjusting the Color TempSetting User Color Temp Chroma TransientSetting the Color Focus Reddish colorMaking the Progressive Scan Settings Frame ModeMotion Setting Jaggies FilterAdjusting Screen Position Position Adjusting Screen Position and SizeAdjusting Screen Size Size Adjusting Audio Adjusting Treble TrebleAdjusting Bass Bass Adjusting Volume Balance BalanceOther Adjustments AdjustmentFeatures setup screen has the following 4 options Adjustment Item Contents of Adjustments OperationOn Screen Menu Selecting the settings of Video/S-video Input terminal Setting the Input TerminalsSelecting the settings of D-SUB Input terminal Auto Off-NO SIG Other SettingsSelecting input terminals Audio Input Minimizing phosphor burn-in Screen Orbiter For RGB Specifying RGB Input Signal Code Setting For mD-sub inputDisplaying white over entire screen White Screen Input Signal Video mode Input Sync. Signal type Setting Exhibition Mode Exhibition ModeDisplaying System Status Information Press Eor Fto select Factory Initialization of User Adjustment ValuePress Cor Dto select the Yes Cleaning and Maintenance Before Obtaining Service