Daewoo DP-42SM, DP-42WM, DP-42GM user manual Before Requesting Service, Function properly

Page 50

Before Requesting Service

Before requesting for a service, check the following points once again.

S t

• Remote control does not

y o

mm

function properly.

p s

 

C• Check for any obstacle between the

Remote Control and the Display.h

e• Check for dead batteries and

cincorrect battery orientation.

k• Check if the Remote Control is the

s right one.

Remove any obstacle between the

Remote Control and the Display.

A

c• Replace batteries and use the correct

tpolarity (+) or (-) of the batteries.

i

o• Use the pertinent Remote Control

nproper to the model.

The Display makes a snapping sound.

Check if the pictures and sound are normal.

This sound is produced due to variations in room temperature.

This sound does not indicate that the Display has a problem if the pictures and sound can be viewed and heard properly.

There are empty spots at the top and the bottom area of the screen.

Check if the screen size of an image is wider than 16:9 aspect ratio (theater screen size).

When video screen is wider than 16:9 aspect ratio, you may see dark areas at the top and the bottom of the screen.

Before Requesting for a Service

S t

• There are spots on the screen

y o

mm

or screen rolls.

p s

 

C• Check if your product is affected by

any interference from automobiles,h

ehigh-voltage transmission lines, neon

csigns or other potential sources.

k s

A

c

t

i

o n

Screen size is suddenly changed.

The screen size of a video image may not be matched to the size of the dark initial screen.

Check by using other video tape.

50

Image 50
Contents Plasma Display Features FCC RF Interference Statement Installation Safety PrecautionsPower While Using Monitor Do not allow children to play or hang on the monitorDo not install where there is oil, smog, moist, and dust During Use Do not place any object or cover on the monitorChecking Accessories Optional Accessories Page Contents Rear Panel ControlsFront Remote Control Installation Instructions When Using the StandConnecting the Speaker to the PDP Watching Digital Broadcasts Press the Power ButtonsPress the Power buttons of the PDP and the Receiver Select a Desired Channel and Function Remote Control or the PDP unitInput Select Video2Watching Cable Broadcasts Watching Cable BroadcastsPDP Turn the PDP and the Receiver onVideo1 Video2 Component2 Component1 Watching Satellite Broadcasts Watching Satellite BroadcastsInput Select button Watching a DVD Image Watching a DVD ImageConnect a DVD Player to the PDP Select a Desired Title and Function PDP unitWatching a VCR Image Watching a VCR ImageConnect a VCR to the PDP Turn the PDP and the VCR onRemote Control or PDP unit Select Video 1 or Video 2 byConnect a Camcorder/Game Console to PDP Turn the PDP Camcorder/Game Console onRemote Control or the PDP Component 1 -- ComponentConnecting PC Connecting PCBefore connecting to the PDP, set Resolution of the PC Connect the PC to the PDPTurn on the PDP and the PC Press the Power buttonResolution of the PC monitor is best at 640 x 480 VGA Sequence is as followsPC Input Resolution Available in PDP Selecting Auto Picture Mode Selecting Auto Picture ModeSelecting Picture Mode One of Four Picture ModesPress the / Button Select the Custom ModeCustomizing Picture Customizing PictureSelect a specific adjustment item Select User Mode AdjustmentsPicture Condition Adjustments PreferenceAdjusting Screen Size Adjusting Screen SizePress the Screen Mode Button Select Screen Select the Screen SizeAdjusting Screen Position and Size Then, adjust the value by pressing or Press the VolumePress the Volume While you are in ‘Screen’ mode, pressEnlarging Screen Size Enlarging Screen SizePress the ‘ZOOM+’ Button Move the Screen Position Watching a Still Image Watching a Still ImagePress the ‘FREEZE’ Button Adjusting Auto Sound Mode Adjusting Auto Sound ModeSelect Sound Mode Menu will DisappearSelect Sound Balance Customizing Sound ModeCustomizing Sound Mode Button to display the followingAdjust it by pressing the / buttons Select the Spatial Effect ModeSelect the Sound Mode Pressing the buttonSelecting Input Signal Press the Input Select ButtonButton Adjusting from Menu ScreenSelect Input Press the Display button on the Remote Control Press the Display ButtonSelecting Languages Select Utility by the / buttonButton Initialization will StartBack to Initialization Press the Sleep Button Setting Sleep TimerSetting Sleep Timer Before Requesting Service Function properlySpecifications