Sanyo LCD-37XR9DA Assembling the stand and removing the stand columnOption, To install the stand

Page 39

Assembling the stand and removing the stand column(Option)

If the stand is provided, please read these instructions thoroughly before attempting this installation.

You must install your TV into the stand in order for it to stand upright on a cabinet or other flat surface. If you intend to mount your TV on a wall or other vertical surface, you must remove the stand column.

Cautions:

Make sure that you handle your TV very carefully when attempting assembly or removal of the stand. If you are not sure of your ability to do this, or of your ability to use the tools necessary to complete this job, refer to a professional installer or service personnel. The manufacturer is not responsible for any damages or injuries that occur due to mishandling or improper assembly.

When using a table or bench as an aid to assembly, make sure that you put down a soft cushion or covering to prevent accidental scratching or damage to your TV's finish.

The speaker is not intended to support the weight of your TV. Do not move or handle your TV by the speaker. This can cause damage to your TV that is not covered by the manufacturer's warranty.

Before attempting assembly or removal of the stand, unplug the AC power cord.

To install the stand:

1. Remove the stand from the box and place it on a table or bench.

You must pay attention to the direction of the stand. The wide portion of the stand should go towards the front of the TV.

2.Lay your TV flat (screen down) on the edge of a table or bench. Make sure that you put down a soft cushion or cloth so that your TV is not scratched.

3.Insert the stand column into the stand socket, move the column steadily until the Locators on the column align with the locating grooves on the stand. And align the holes in the stand with the holes in the stand column, then secure the stand to the column with four M5 screws(provided).

Locators

Locating grooves

Stand

M5 screws

To remove the stand from the TV, perform these steps in reverse order.

36

Image 39
Contents LCD TV Important Information Table of Contents Important Safety Precautions Important Safety Precautions To clean this unit, wipe with a soft, dry cloth Important NoticeDo not use in hot and cold rooms locations Using the Remote Control Installing the BatteriesPreparations Antenna Connection Power ConnectionVOL+ Identification of ControlsMain Unit front view/side view CH+Main Unit rear view Colored buttons RED/GREEN/YELLOW/BLUE Direct Remote Control UnitCoaxial HIFi System Connecting digital coaxial audioConnections Coaxial cableConnecting an Hdmi device Connecting a CamcorderTo play component video from an external device Connecting Component VideoConnecting a Computer To connect a device using component videoConnecting a VCR for Recording Connecting HeadphonesTo record program To navigate through the OSD main menu Basic OperationsMain Menu Overview List of main menus to help you with operationsTurning Off Turning On/Off the PowerFirst Time Setup Turning OnSelecting the Input Signal Source Displaying the Information BannerPress 3,4or OK to confirm the selection Memorizing the Channels Auto Channel SearchManual Searching for DTV programs Manual Fine Tuning Setting Audio SystemManual Searching for ATV programs Setting Favorite Channels Labeling ChannelsOpen the Programme Edit menu To delete channels Channel List ManagementTo skip unnecessary channels To sort channelsChannel and Program Selection Customizing the Picture Picture AdjustmentUsing the volume buttons VOL+ and VOL Sound AdjustmentAdjusting the Volume Adjusting the SoundIGR German stereo system Broadcasts Stereo/Bilingual Selection for analog channelsAudio Track Selection for digital channels Nicam Broadcast SelectionHearing Impaired System SetupSystem Setup System Update TimeTo create a new password Rating and Lock SetupPassword Setup Block Program SetupParental Guidance Setup DTV only Lock Tuning SetupRestoring Factory Default Time Zone Selection Timer SetupCurrent Time Setup On Timer SetupOff Timer Setup Sleep Timer SetupAuto Sleep Setup Press Yellow button again to exit EPG OperationOpereation Program’s information will be displayedTeletext & Subtitle TeletextSubtitle Such as position and phase Screen Setup for D-SUBPC ModeScreen Setup Auto adjustHotel Mode Setup Hotel Mode SetupHotel Mode Troubleshooting Remote control does not operateDouble images Select them with 0-9 number buttons Current input modeOne or some channels can’t be Displayed SectionLCD TV SpecificationsAssembling the stand and removing the stand columnOption To install the standTo remove the stand column 5944035230 Ver