SPECIFICATION / HELPFUL HINTS
| Specification | |
|
| |
Common specification |
| |
Power source | AC 220~240V 50Hz | |
Television system | System I | |
Colour system | PAL |
|
| (PAL/NTSC3.58 in AV mode) | |
Channel coverage | UHF: | |
Aerial input impedance | 75 ohm | |
AV terminal |
|
|
| AV1: CENELEC Standard | |
| Input: Composite video, RGB and | |
| ||
|
| |
| AV2: | CENELEC Standard |
| Input: Composite video, RGB, | |
|
| |
| ||
|
| and |
| AV3: CENELEC Standard | |
| Input: Composite video, and | |
Side AV terminal |
|
|
| AV4: | RCA jacks |
| Input: Composite video and | |
Headphone socket | Mini Jack | |
The following faults are not caused by the receiver:
"GHOSTS"
Reflections of signals from mountains or high buildings will cause multiple images, called "Ghosts". These abnormal conditions can be reduced to minimum by repositioning aerial or by installing new one suited for your area.
"INTERFERENCE"
Interference may be caused by electrical appliances, car ignition systems, etc. This should normally be a temporary condition, but should this interference persist, contact your dealer.
■Plug and Play Helpful hints.
If you do not fit an aerial into this TV set the Plug and Play feature may start up each time you switch on your TV.
To prevent this follow these instructions.
1.Switch on your TV set, the Plug and Play screen appears.
2.Press the MENU button on the remote control to clear the Plug and Play screen.
3.A second screen will appear. Press the Return key to clear from the screen.
4.Press the D/A key to return to Analogue.
5.Press the MENU button to select the Menu screen. (as shown below).
|
|
|
|
|
|
Sound output |
|
|
(Continuous) | 2 x 10W | 2 x 10W |
Contrast Ratio | 900:1 | 1000:1 |
Screen(inches) | 27 | 32 |
(viewing measured diagonally) |
| |
Display Resolution | 1280 x 720 (WXGA) | 1366 x 768 (WXGA) |
Viewing angles | H:176°, V:176° | H:176°, V:176° |
Dimensions |
|
|
(WxHxD mm) | 800 x 470 x 239 | 922 x 545 x 239 |
(including stand) |
|
|
Weight (kg) | 14.4 | 17.5 |
(including stand) |
|
|
Timer
Sound
Setting
| Preset |
|
|
|
| Auto Tuning |
| v | |
Picture | Auto Sort |
| v | |
Prog. Preset |
| v |
| |
|
|
| ||
| Swap |
| - - |
|
|
|
| ||
| Fine Tuning |
| vv | |
|
|
|
|
|
6.Select Preset Menu by pressing the 1or 2button.
7.Select Prog. Preset by pressing the 6or 5button and enter Semi by pressing the 1button.
8.Press the 6button and select Memory. Press OK button to cancel. (The OK? changes to OK).
Helpful hints
■NO PICTURE, NO SOUND
● Check if TV is plugged in.
● Try a different channel, if OK, probably station trouble.
■POOR PICTURE, SOUND OK
●Adjust BRIGHTNESS control.
●Adjust FINE TUNING control.
●Check aerial connections.
■NO COLOUR, PICTURE OK
● Adjust COLOUR control.
● Adjust FINE TUNING control. ● Is the programme in colour ?
■WEAK PICTURE
●Check aerial connections on back of set.
●Check aerial for broken wires.
●
Semi |
|
|
|
| |
Channel |
| C24 |
Position |
| 01 |
Skip |
| OFF / ON |
Memory |
| OK? |
|
|
|
9.The next time you switch on your TV set the Plug and Play screen will not appear.
21