To search a preset station by PTY codes
A particular programme type broadcast can be located by specifying the PTY codes.
1.Press the RDS button to select “PTY” while listening to an FM broadcast.
2.Press the TUNE/PTY + or – button within 2 seconds to select the desired PTY code. The PTY code changes as shown below;
NEWS vAFFAIRS vINFO vSPORT vEDUCATE vDRAMA v CULTURE vSCIENCE vVARIED vPOP M vROCK M vM.O.R. M vLIGHT M vCLASSICS vOTHER M vWEATHER vFINANCE vCHILDREN vSOCIAL vRELIGION vPHONE IN vTRAVEL v HOBBIES v JAZZ v COUNTRY v NATION M v OLDIES v
FOLK M vDOCUMENT vTEST vALARM (or in the reverse sequence)
3.Press the PTY CHK (e) button within 4 seconds.
The unit searches 24 preset stations and stops when it finds a broadcast of the PTY code you have selected, then tunes into that station.
-To continue searching after the first stop, repeat steps 1 - 3 above.
-If no broadcast is found, the original station is heard.
To cancel searching, press the RDS button.
TIMER OPERATION
Using the timer
Set the on and off times, function to be used and volume level. Operation will start with the selected function at the on time. The sound will be gradually increased from a
The timer will function every day unless it is released.
Preparation
Note:
Make absolutely sure that the clock is set to the correct time before setting the timer.
-Select the function for timer operation and prepare the sources to be used.
-If the function selected is tuner, tune in to the desired band and station.
-Adjust the volume level as desired.
Operation
1. Press the SHIFT + 7 TIMER buttons.
ON
The previous timer on time setting appears.
2. Press the SHIFT + 8 ADJUST buttons within 10 seconds.
ON
3.Set the hours of timer on time by pressing the eor fbutton, then press the SHIFT + 8 ADJUST buttons.
ON x | ON |
Set the minutes in the same way.
ON x | OFF |
The timer off time setting appears.
4.Set the timer off time as described in step 3. The original display returns, then the timer operation standby mode is activated. “0” remains lit.
5.Press the z/ON button to switch off the power, you will see GOOD BYE and “0” this will go off after 2 seconds.
-“0” blinks during a
-If you wish to switch off the power during a
To check the timer settings
Press the SHIFT + 7 TIMER buttons repeatedly. The timer settings are displayed in the following order:
On time v Off time vFunction v Original display returns
To change the settings, press the SHIFT + 7 TIMER buttons to select the setting to be changed, then press the SHIFT + 8 ADJUST buttons so that the display blinks. Change the setting as explained above.
To release the timer
After turning the power on, press the SHIFT + 7 TIMER buttons, then press the SHIFT + 9 SET/CLEAR.
To set the timer again with the same settings
1.Press the SHIFT + 7 TIMER buttons, then the SHIFT + 9 SET/CLEAR.
2.Press the z/ON button to switch off the power.
Note:
-If the SHIFT + 9 SET/CLEAR buttons are pressed while the timer is being set, the original display returns.
-The timer mode is released if a power failure occurs during timer controlled operation.
-The timer may not operate if a power failure occurs during timer operation standby mode.
Using the sleep timer
The sleep timer automatically switches off the power after a preset time has elapsed. The volume will gradually be reduced
Press the SHIFT + 6 SLEEP buttons repeatedly to select the desired sleep time. “SLEEP” and the selected time blink on the display. After several seconds, the original display returns and the brightness of the display reduces. “SLEEP” blinks.
To check the remaining sleep time
Press the SHIFT + 6 SLEEP buttons once. After several seconds, the original display returns.
To release the sleep timer while in operation
Press the SHIFT + 6 SLEEP buttons, then press the SHIFT + 9 SET/ CLEAR buttons. The timer is also released if the power is switched off.
22