Zenith R40W46 warranty Programming the Remote to operate other devices

Page 33

Programming the Remote to operate other devices

The remote control for your projection TV is a multi-brand or universal remote control. It can be programmed to operate most remote-controllable devices of other manufacturers.

Note that the remote control may not control all models of other brands.

1.Test your remote control.

To find out whether your remote control can operate the IR device without programming, turn on the IR device such as a VCR and press the corresponding mode button (VCR) on the remote control, while pointing at the IR device. Test the POWER and CH +/- buttons to see if IR device responds properly. If not, the remote requires programming to operate the device.

2.Turn on the IR device to be programmed, then press the corresponding mode button on the remote control.

3.Press the POWER and MUTE buttons simultaneously, the remote control is ready to be programmed for the code.

4.There are two ways to find the right code for the IR device.

A. If you press the CH +/- buttons repeatedly, the codes will change one at-a-time. Press the POWER button after each code change. If the right code is found, the device will turn off.

B. Enter a code number using the number buttons on the remote. Programming code numbers for the corresponding component can be found on the following pages. Again, if the code is correct, the device will turn off.

5.Press the EXIT button to store the code.

6.Test the remote control functions to see if the IR device responds properly. If not, repeat from step 2.

2

4

tv

vcr cable dvd sat

mode light power

tv/video comp/dvi sleep

arc cc flashbk

1

2

3

4

5

6

7

8

9

video

0

audio

fcr

 

mute

vol ch

pip pipch- pipch+ swap

still pip input position mts

up

enter

leftright

menuexit

down

play pause stop record

rew ff

skip

3/4

3

4

5

33

Image 33
Contents Installation and Operating Guide Warranty Power Cord Polarization Important Safety Instructions From previous Outdoor Antenna Grounding Contents Remote Control Key Functions Swap FlashbkPIP Input PositionRemote Control Sensor Remote Control Key Functions / TV SetupLED Light Emitting Diodes Displays IndexTurning the TV On/Off Basic TV Setup and OperationChannel Search Basic TV Setup and OperationFinding Channels with EZ Scan You can also add or delete channels manuallyAdjusting the Sound Level Tuning ChannelsClock Setup Auto/Manual FeaturesAuto Off Setup Off Timer/On Timer SetupFeatures Sleep Timer SetupKey Lock Setup Fine Tuning Adjustment Signal Reception BoosterFavorite Channel Memory Using the Menu Using the arc ButtonPicture Format Selection Auto MoveEZ Video Setup Picture SetupCinema Mode Setup DRP Digital Reality PictureVM Velocity Modulation Setup Picture SetupACC Auto Color Control Setup User Picture Appearance AdjustmentsDarken the room before adjusting color convergence Color Convergence AdjustmentStereo/SAP Broadcasts Setup Sound SetupEZ Audio set up using the audio button EZ Audio set up using the Audio menuAVL Auto Volume Leveler Adjusting Balance, Treble, BassTV Speaker On/Off PIP Picture-in-Picture /Twin Picture Moving the Sub Picture in PIP modeWatching PIP Picture-in-Picture Main Picture Sub PicturePIP Mode Twin Picture ModePOP Picture-Out-Picture Channel Search and Display Still Picture FreezeClosed Captions Using Closed CaptionsSelecting Caption/Text Mode Captions On, Off, EZ mute SetupCaptions set up using the cc button Captions set up using the Captions MenuParental Control Overview Content CategoriesChip Rating and Categories For Movies Previously Shown in Theaters Movie RatingsBlocking Scheme Setup Canadian English language rating systemCanadian French language rating system Connecting a Catv Cable Connecting an Outdoor AntennaOhm Flat Wire Antenna ConnectionsEZ Notice Make A/V Connection External Equipment Connection and Viewing SetupHere is an example drawing of a typical jackpack layout Select DVIMonitor Out Setup External Equipment Connection and Viewing SetupsVCR Connections VHS VCR ConnectionsDVD Player Connection External Stereo Amplifier/SpeakersAnalog/Stereo Amplifier DVD PlayerExternal Equipment Connection and Viewing Setup DTV Set-top Box ConnectionDTV Receiver There are two ways to find the right code for the IR device Programming the Remote to operate other devicesVCRs Programming CodesDVD SATCatv Programming CodesScreen Cleaning MaintenanceCabinet Cleaning Extended AbsenceProduct Specifications Troubleshooting Checklist SymptomsCheck These Things Zenith Electronics Corporation