Winegard MV3500T manual 1800788-4417 Yes

Does the unit

lock on the

signal?

Do you lose the signal

No

Yes

when you start

moving?

No

Yes

Does the unit reaquire the

signal shortly after losing it?

Does the unit only lock

Yes

No

onto a signal while the

Do the switch settings

coach is moving?

The unit must travel in

No

Yes

match the mounting

a straight line for 10

seconds or more than

option used?

No

Yes

Is the Gyro board

Does the unit toggle to the

10 MPH to keep a

connected?

secondary satellite as

signal when you first

Yes

No

needed?

start moving.

Set the

Are the switch

Yes

No

switches for the

settings fully in the up

mounting

or down position as

needed?

Call Winegard

Is the receiver set up as

option used.

Replace the

Reconnect.

No

Yes

Gyro board.

Technical

shown in the Operation

Service

Manual for the MV3500T?

Using a small screw

Do you have a GPS

1(800)788-4417.

No

Yes

driver, push each

antenna with this unit?

switch fully into place.

No

Yes

Is the GPS antenna

Are you using an HD,

Refer to pages 3-4 in the

connected to the

MV3500T Operation

Dual or recordable

Do you have a

electronics?

receiver?

Gyro board inside

No

Yes

Manual for proper

No

Yes

receiver set up.

the Electronics

box?

Yes

No

Reconnect the

Disconnect the

Refer to the receiver

Please try a D10

GPS antenna.

antenna. Is the

manual to reset the

receiver for DirecTV or a

Is the mini USB

center wire of the

Does the dish start

reveiver.

311 receiver for DISH

This is not a

GPS cable bent?

connecting the Gyro

Network.

No

Yes

moving again?

Board to the Main

tracking unit, it will

No

Yes

electronics plugged in?

not work while the

Does the unit seem to

If the problem persists,

No

Yes

coach is in motion.

Is the GPS cable

repeat the process after

call Winegard

damaged or

it has started a search?

Technical Service

Reconnect the

Replace the

pinched anywhere

Yes

No

1(800)788-4417.

USB cable.

GPS antenna.

along its length?

No

Yes

Connect the power

Does the receiver

directly to a Good Fully

display a signal

Is the GPS

Replace the

during

search?

Charged 12VDC battery.

No

Yes

installing in the

GPS antenna.

Does the dish change

open, 3 feet from

any obstruction?

elevation during the

Do you have 12-18VDC

No

Yes

search?

on the coax connected

No

Yes

Is the base of the

to the LNBF?

satellite dish level?

Is the mini USB

No

Yes

No

Yes

Move the GPS

Is the elevation

for the Gyro

antenna to an

Replace the LNBF.

motor connected?

open area on

Board connected?

Follow the coax back

No

Yes

Level the unit. The

Yes

No

Does the unit have

the roof.

to the receiver from

base must be within

a clear view of the

the LNBF. Check

Connect the

3 degrees of level

southern sky?

each connection until

Do you see a signal

Can you move the

to function properly.

Replace the

Reconnect the

No

Yes

you find the voltage.

elevation motor.

elevation motor

Gyro Board.

Gyro Board.

on the signal meter

during the search?

while the power

No

Yes

is off?

Move to an open

Is the receiver set

If you are losing the

No

Yes

area. The unit must

up as shown in the

voltage in the

have a clear view of

satellite dish

Electronics, replace

Replace the

Replace the

the southern sky to

manual?

the Electronics.

Is the receiver set up

Yes

No

elevation motor.

see the signal.

Do you have an

correctly according to

Electronics.

unobstructed view of

the Movn’ View

Set the receiver as

the Southern sky?

manual?

Does the unit seem to

shown in the manual.

No

Yes

No

Yes

stop on something with

Refer to pages 3-4 in

out showing a signal?

the Operation Manual.

Are you able to turn the

Yes

No

Move the vehicle to a

Replace the

Correct the

Replace the

elevation drive screw by hand?

No

Yes

location that provides

Electronics.

receiver set up.

Electronics.

Is the unit connected

a clear view of

directly to a 12VDC

the Southern sky?

Does the elevation motor

battery?

change direction after it hits

No

Yes

the elevation limit switch?

Are the switches set

No

Yes

Is the arm on the

Connected it directly

Does it work using

correctly for your

elevation limit switch

to a good fully charged

another receiver?

receiver?

Yes

being fully engaged?

12VDC battery.

No

Yes

No

Yes

No

Are the switches

Refer to pages 3-

Replace the

Replace the

Replace the

Replace the

pushed fully into

electronics.

receiver.

4 in your manual

place?

Elevation Limit

Elevation Motor

to set these

No

Yes

Switch.

Assembly.

switches.

Straighten the

wire and

reconnect the

cable.

Printed in U.S.A. © Winegard Company 2006 • Winegard Company	Using a small	Turn off the unit and	MV3500T
	screw driver,	reset your receiver.
3000 Kirkwood Street • Burlington, IA 52601-2000 ?????	push each swich	Refer to the receiver’s
	fully into place.	manual for this process.