Digital Elevation Sensor Interior Wallplate

Digital Elevation Sensor Interior Wallplate

STEP 19. See Figure 17. If using the SM-1000 surface mount box, feed cable through hole in box.

STEP 20. Connect wires coming from sensor on roof to wall plate display in vehicle. It is important

to properly connect the wires at the roof and the wall plate. (Plug will click when inserted properly.) The system is designed to use a 9 volt battery OR

+12 VDC from vehicle. Do not use both! IMPROPER WIRING WILL

CAUSE DAMAGE TO THE PRODUCT,

SEE FIGURE 18.SM-1000

Surface Mount Box

STEP 21. Pressing the button when

the antenna is in a vertical position should display 24 (+1°). Display will automatically turn off after 1 minute.

STEP 22. Check connectors and cable entry points. Be sure these areas are properly sealed to prevent water damage.

FIGURE 18

FIGURE 17

Cable and plug from roof sensor unit; plugs into sensor

Sensor to readout cable

Readout assembly

Snap battery in place, making sure battery terminals are firmly seated on wall plate terminals.

Based on 5 minutes a day of usage, standard new alkaline batteries should last 88 days.

OPERATION (Also on pages 2-3)

STEP 23. Using satellite receiver, find correct eleva- tion for your location. See the receiver manual for details of setup information.

STEP 24. Press button on Winegard digital display wall plate. If antenna is in travel position, the display will show LL for Low Limit.

STEP 25. Crank elevation handle to raise antenna. Stop when readout displays correct elevation for your location. (Found on receiver setup menu.)

STEP 26. Rotate antenna VERY SLOWLY until correct satellite signal is acquired. Note: 3° and stop. DO NOT rotate continuosly even if you’re rotating slowly. If the elevation angle has changed, it could be due to the following —

•Vehicle is not parked level.

•Antenna system mounted on slightly sloped roof. If this is the reason, after you have rotated the antenna to the approximately correct compass direction, adjust to correct elevation and continue research.

Special Note: When you have found the satellite sig- nal, adjust the antenna u/down and right/left for the strongest signat your receiver displays. due to varia- tion in receivers and installation methods, you may find the elevation numbers after peaking on strongest signal no long match what the receiver display rec- ommended. This is normal. The elevation sensor should always get your close enough to pick up a signal to peak on. If display turns off while you’re searching, just push the button for another minute of operation. Whith a little practice, most users find the signal in 30 to 50 seconds.

RMFLDM4, RM-DM46, RMDM04, RM-DM00 specifications

Winegard is a well-known manufacturer of advanced antenna technology, and its products are designed to provide high-quality reception for broadcast television. Among its lineup, the Winegard RM-DM00, RMFLDM4, RMDM04, and RM-DM46 antennas stand out for their exceptional features and efficiency.

The Winegard RM-DM00 is a compact, multi-directional antenna that is engineered for optimal performance in urban areas with significant electronic interference. Its unique design allows it to capture over-the-air signals from multiple directions, ensuring a robust signal and exceptional picture quality. With a sleek and discreet profile, the RM-DM00 can be easily mounted on rooftops or exterior walls, offering versatility in installation options.

Next in line, the RMFLDM4 is a flat antenna known for its ultra-thin design and no-obstruction capabilities. This antenna employs advanced filtering technologies that minimize noise and enhance signal clarity. Its sleek aesthetic makes it an ideal choice for modern interiors, allowing homeowners to place it in living rooms or offices without disrupting the decor. The RMFLDM4 is engineered to pick up both VHF and UHF channels, making it a versatile choice for users in various regions.

The RMDM04 is a durable and weather-resistant model designed for outdoor usage. This antenna is perfect for those living in rural areas, where signal ranges can be challenging. Equipped with advanced amplification technology, the RMDM04 can extend the range of signal reception enough to capture long-distance broadcasts, ensuring viewers enjoy uninterrupted access to their favorite channels, even in remote locations.

Lastly, the RM-DM46 is designed for superior performance, boasting dual UHF/VHF reception capabilities. This model includes a built-in signal amplifier that boosts weak signals while reducing noise for the ultimate viewing experience. The RM-DM46 is versatile and easy to install, compatible with most devices, making it a favorite among cord-cutters who wish to access free, high-quality television content.

Overall, each of these Winegard antennas—RM-DM00, RMFLDM4, RMDM04, and RM-DM46—offers unique features and technologies designed to maximize signal reception while ensuring reliability and ease of use. Whether for urban settings or rural landscapes, Winegard's antennas effectively enhance viewers' experiences, allowing them to enjoy a diverse range of channels with excellent picture quality. With these options, users can find the perfect match for their television needs, underscoring Winegard's commitment to innovation and performance in the antenna market.