Palsonic 6140G owner manual Channel selection, To watch a TV programme

Page 14

OPERATION

Channel selection

You can watch TV programmes being broadcast on the preset channels.

To watch a TV programme

You can select your desired TV program by one of the following methods.

Using the direct select buttons

 

To select a one-digit position number (0~9)

 

 

 

 

 

 

 

 

 

METHOD 1: Press the button and the screen displays "X- -", wait for 2

 

 

 

 

 

After 2

 

X--

 

 

seconds and the channel is selected.

 

 

 

 

 

seconds

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

METHOD 2: Press 0 button and the screen displays "0- -", then press 0

 

 

 

 

 

 

X

 

 

 

 

 

 

 

 

 

button again, the screen displays "00-" then press the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

numbers. (The period of two-press must be within 2 seconds).

 

 

 

 

 

To select a two-digit position number (10~99)

 

 

 

 

 

 

 

X--

 

METHOD 1: Press these two numbers and the screen displays "XX -", (The

 

 

 

 

 

 

 

 

period of two-press must be within 2 seconds). Wait for 2

 

 

 

 

 

 

 

 

 

 

seconds and the channel is selected.

 

 

XX-

 

METHOD 2: Press 0 button first, than press these two numbers, the screen

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

displays "0XX", the channel is selected. (The period of

 

 

 

XX

 

 

 

 

 

 

 

two-press must be within 2 seconds).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To select a three-digit position number (100~255)

 

 

 

 

 

 

 

 

 

 

X--

 

 

Press these three numbers and the screen displays "XXX" the channel

 

 

 

 

 

is selected. (The period of two-press must be within 2 seconds).

 

 

 

 

 

 

 

 

 

 

 

 

XX-

 

NOTE: If the input number is over 255, the screen will remain at the

 

 

 

 

 

 

current viewed program.

 

 

 

 

 

 

 

 

 

 

 

 

XXX

 

 

Using the CH

buttons

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press CH to select lower position numbers; CH to select higher ones.

2

1

3

Using the PREVIOUS channel button (

)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When there are no menus on the screen, pressing the

 

 

 

 

 

 

11

 

button on the remote controller (below the MENU button)

 

 

 

 

 

 

 

 

2

 

 

 

 

can swap the current viewed channel with the previous

 

 

 

 

one. For example, the channel you previously watched is

 

 

 

 

 

 

 

 

11, the present channel is 2, press the button, it will

 

 

 

 

 

 

 

 

return to channel 11, press the

button again it will

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

return to channel 2.

 

 

 

 

 

 

 

 

Using the channel SCAN button

Press SCAN button, the set will scan the channels from first channel to higher channels one by one, every program will be displayed for about 3 seconds and then go on scanning until all programs are scanned over and then return to your former viewed program. During the scanning, press SCAN button again, the set will return to your former viewed program.

12

Image 14
Contents 61CM Cordless Remote Colour Television Australia 1300 657Contents Introduction Page Antenna Connection Battery installationEffective range of the remote control operation Front view Back ViewRemote Controller Remote Controller for Model 6140GMenu Introduction Introducing the menuTurning the Power On/Off To turn the power on/offTo enter into menu TuningTo preset channels Auto search LllllllllllllTo preset channels Manual search Manual searchTo skip a position number To restore skip a position numberMFT Manual Fine Tuning Setting of colour system Auto PAL 443NTSC 358NTSCChannel selection To watch a TV programmeSelectable picture To select the picture modeConvenient Picture Controls To set the desired picture quality to the Personal positionSleep timer Convenient Sound Controls and Sleep timerAdjusting the volume and muting the sound Colour system selection System settingTo select the language for the OSD Blue backgroundPlaying games Special functionsCalendar function To play GAME1 GobangTo play GAME2 Falling Cube OFF Time setting NOW Time settingOn Time setting On Channel settingChannel reservation Time settingChannel setting To reserve the channelExternal Equipment Connections To connect AV input terminalsTo connect Monitor output terminals TV Video 1 Video 2 Video 3 S-VIDEO1Symptoms Check the following items Troubleshooting GuideSpecifications 604-A2533-02