Palsonic PDP4220HD owner manual Troubleshooting, Remote control does not operate, Double images

Page 34

Troubleshooting

If, after reading these operating instructions, you have additional questions related to the use of your television, please call the services center in your local area.

Before calling service, please check the symptoms and follow suggested solutions.

Remote Control

Problem

Remote control does not operate

Possible Solutions

!The batteries could be weak. Replace the batteries.

!Check the orientation of the batteries.

!Make sure the power cord is plugged in.

Video and Audio

Problem

Possible Solutions

No picture (screen not lit), No sound

!Make sure the power cord is plugged in.

!Press POWER on the TV or on the remote control.

!Try another channel; it could be station trouble.

Dark, poor or no picture (Screen lit), good sound

!Select a proper picture mode.

!Adjust the brightness in the video setting.

!Check the antenna connections.

	No color/dark picture/color	!	Adjust the color saturation in the video setting.
	is not correct	!	Adjust the color saturation in the video setting.
	is not correct

	Only snow and noise appear	!	Check the antenna connections.
	on the screen	!	Try another channel; it could be station trouble.

	Dotted lines or stripes	!	Adjust the antenna.
		! Move the TV away from noise sources such as cars, neon signs, or hair dryers.

	Double images	!	Using a highly directional outdoor antenna or a cable may solve the problem.

	Good picture, no sound	!	The sound may be muted. Press MUTE again to cancel.
		! Make sure the stereo mode is set to stereo or mono.

	Audio noise	!	Communication problems may occur if infrared communication equipment (e.g.,
			infrared cordless headphones) is used near the TV. Move the infrared
			communication equipment away from the TV until the noise is eliminated.

31

Image 34

Contents N111 AUSTRALIA1300 657Important Information Table of Contents Important Safety Precautions Important Safety Precautions Important Notice To clean this unit, wipe with a soft, dry clothDo not use in hot and cold rooms locations Installing the Batteries Using the Remote ControlPreparations Power Connection AntennatennaConConnectionectionIdentification of Controls Indicator/Remote Sensor CH+Power Main Unit front view/side viewMain Unit rear view Remote Control Unit Connections Connecting a CamcorderHow to connect TV Left SideTo connect a device using component video Connecting Component VideoConnecting a Computer To play component video from an external deviceHow to connect a device using Hdmi Connection Connecting an Hdmi deviceConnecting a VCR for Recording To play from the device using HdmiConnecting Headphones Connecting Digital Coaxial AudioCoaxial audio cable Pdif in Coaxial Audio Processor List of main menus to help you with operations Basic OperationsMain Menu Overview To navigate through the OSD main menuDisplaying the Information Banner Turning On/Off the PowerSelecting the Input Signal Source Turning OnAuto Channel Search Memorizing the ChannelsManual Searching for DTV programs Setting Audio System Manual Fine TuningManual Searching for ATV programs Labeling Channels Setting Favorite ChannelsOpen the Programme Edit menu To sort channels Channel List ManagementTo skip unnecessary channels To delete channelsChannel and Program Selection Picture Adjustment Customizing the PictureAdjusting the Sound Sound AdjustmentAdjusting the Volume Using the volume buttons VOL+ and VOLNicam Broadcast Selection Stereo/Bilingual Selection for analog channelsAudio Track Selection for digital channels IGR German stereo system BroadcastsLanguage System SetupSystem Setup Hearing ImpairedBlock Program Setup Rating and Lock SetupPassword Setup To create a new passwordLock Tuning Setup Parental Guidance Setup DTV onlyRestoring Factory Default On Timer Setup Timer SetupCurrent Time Setup Time Zone SelectionSleep Timer Setup Off Timer SetupAuto Sleep Setup Opereation EPG Operation Program’s information will be displayed Teletext Teletext & SubtitleSubtitle Auto adjust Screen Setup for D-SUBPC ModeScreen Setup Such as position and phaseRemote control does not operate TroubleshootingDouble images Displayed Section Current input modeOne or some channels can’t be Select them with 0-9 number buttonsSpecifications PDP TV5944034820 Ver