BassKick 100
•A headset is plugged in so that the speaker is switched off. | 8 Technical Data |
|
| |
Plug off the headset to play via the internal speaker. |
|
|
|
|
| Security Specifications |
|
| |
When using the LINE OUT socket, there is a humming noise. | Mains input voltages: 240V, | |||
•An electrical / magnetic alternating field intersperses onto the | Primary fuses: | 240V | T1A |
|
conduit. Use a better cable and try to minimise the interspersion by |
| T1A |
| |
another passing of the conduit. If this does not help, the utilisation |
| 120V | T2A |
|
of a DI box is recommended. |
| 100V | T2A |
|
•Due to the earthing of the connected devices, a hum | Secondary fuses: |
| 2 x T2,5A | |
emerges. Do in no case interrupt the ground wire of the devices but | Power consumption: | 255 watts | ||
do, if possible, operate both devices at one joint power distribution! | Ambient air temperature in operation: | |||
If this is not possible, the connection must be separated galvanically |
|
|
|
|
by means of a DI box. | Inputs |
|
|
|
| INST. INPUT: | Socket: |
| Jack, unsymmetrical |
When connecting a mixer at the LINE OUT, the signal on the PA is |
| Input impedance: |
| 1 MOhm |
completely distorted. |
| Sensibility: |
| - 23,5 dBV |
•The input of the mixer is not switched to line level. Switch the |
| max. input level: |
| + 9,3 dBV |
input of the mixer to line level. If this is not possible, assign an | FX | Socket: |
| Jack, unsymmetrical |
unsymmetrical (line) input at the mixer. |
| Input impedance: |
| 48 kOhm |
The amp is too quiet. |
| max. sensibility: |
| - 6 dBV |
•A device that is operated in the loop causes level losses. The effects |
| max. input level: |
| +13,5 dBV |
pedal must be levelled by means of its input/output controller. |
|
|
|
|
| Outputs |
|
|
|
The amp sounds too dull | FX | Socket: |
| Jack, unsymmetrical |
•The tweeter is switched off |
| Output impedance: | 220 Ohm | |
|
| Output level: |
| - 6 dBV |
7Maintenance and care | LINE OUT: | Socket: |
| Jack, unsymmetrical |
| Output impedance: | 220 Ohm | ||
The BassKick™ amps are |
| Output level: |
| 0 dBV |
basic rules, the compliance with which secures the high useful life of | Headphones: | Socket: |
| Stereo jack |
your amp: |
| Impedance: |
| |
•Do always provide for a technically unobjectionable device periphery! | Speaker equipment: | 1 x 15" Eminence Bass, 4 Ohm | ||
•Do always provide for free air circulation at the cooling surface of |
| 1 x Leson ceramics tweeter, 4 Ohm | ||
your amp. | Cutoff frequency: | 5 kHz |
|
|
•Do in any case avoid heavy mechanical shocks, extreme heat and |
|
|
|
|
the permeation of dust and moisture. |
|
|
|
|
•Do meticulously observe the specifications of additional devices. | Dimensions (w,h,d) and weight: |
| ||
Do never connect outputs with too large levels (e.g. power | Dimensions: | 498 x 565 x 355 mm |
|
|
amplifiers) to the inputs of the amp. | Weight: | 25.5 kg |
|
|
•Do always check the existing mains voltage before connecting |
| 55 lbs |
|
|
the amp to the mains supply. In case of doubt, contact the stage |
|
|
|
|
technician, caretaker or similar persons. |
|
|
|
|
•Please do never try to repair your amp yourself! Even the exchange of internal fuses should be carried out by an experienced technician only.
•The housing surface or the metal surfaces are at best cleaned with a soft dry cloth. Do in no case use alcohol or other solvents!
english
7