Memorex MVD2037 manual Overloading, Object and Liquid Entry, Outdoor Antenna Grounding, Servicing

Page 5

IMPORTANT SAFETY INSTRUCTIONS (CONTINUED)

should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

15. OVERLOADING

Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

16. OBJECT AND LIQUID ENTRY

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid on the product.

17. OUTDOOR ANTENNA GROUNDING

If an outside antenna is connected to the product, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electric Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge product, size of grounding conductors, location of antenna discharge product, connection to grounding electrodes, and requirements for grounding electrode.

18. SERVICING

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19. REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

20. SAFETY CHECK

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

21. WALL OR CEILING MOUNTING

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

22. DAMAGE REQUIRING SERVICE

Unplug the product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the product. c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

e. If the product has been dropped or the cabinet has been damaged.

f. When the product exhibits a distinct change in performance-this indicates a need for service.

23. HEAT

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

24. NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

￿￿￿￿￿￿￿￿￿ ￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

4

Image 5
Contents User’s Guide Contents Surge Protectors Important Safety InstructionsFCC Notice FCC CautionAccessories CleaningPower Sources POWER-CORD ProtectionSafety Check Replacement PartsDamage Requiring Service OverloadingPower Source PrecautionsUse a soft, dry cloth for cleaning To Obtain a Clear PictureLocation of Controls Remote Battery Installation Remote ControlEffective Distance of the Remote Control Transmitter Battery PrecautionsConnection Connecting the DVD to a TV Using the S-VIDEO Output JackLine Digital PROGRESSIVE-SCAN Component Video Output Connecting the DVD to a TV Using the Y/PB/PR JacksProgressive Y, PB, PR Video OUT Front Right Speaker Connecting the DVD to a Home Theatre SystemFront Left Speaker Television Playable Discs About DiscsDisc Types DVD Audio CDRegion Management Information OFF Setup MenuTV Display TV Type General Setup MenuAngle Mark OSD LanguageCaptions Speaker Setup MenuScreen Saver DownmixDynamic Mode Dolby Digital Setup MenuAudio SubtitleParental Disc MenuDefault PasswordBasic Operation General 3D Sound Audio Mode Audio CD/VCD onlyMute DisplayPlayback of a DVD DVD Basic OperationPAUSE/STEP SLOW/R and SLOW/FSearch Repeat Playback TITLE/CHAPTER SearchTITLE/TIME Search DVD Menu Title Menu Audio MenuZoom AnglePlayback of AN MP3 CD MP3 Basic OperationRepeat Play Forward /REVERSECD/VCD Basic Operation Selecting TRACKS/FILES UsingPlayback of a CD/VCD Number ButtonsRepeat A-B Play Random Playback Important Note on VCD Repeat PlaybackPBC VCD only To Cancel the Program FunctionProgrammed Playback Picture CD Basic Operation Symptom Possible Cause Possible Solution General Troubleshooting GuideProgressive Scan Symptom Possible Cause Possible Solution DVDVCD Video CD Caring for Discs Care and MaintenanceCleaning the unit Compact Disc Video CD SpecificationsMemcorp, Inc Weston, FL