Marantz DL5500 specifications Picture-In-Picture Pip, PIP button, Single Mode PIP, Split Mode PIP

PICTURE-IN-PICTURE (PIP)

Your MARANTZ Projection TV incorporates Dual Tuner technology designed for improved viewing enjoyment. This Dual Tuner feature allows you to view antenna inputs on both the main picture and sub-picture simultaneously, with separate tuning control for each. The Dual Tuner can operate with only one input (ANT A only) or two inputs (ANT A and ANT B).

ANT A input can be viewed as both the main picture and the sub-picture simultaneously. ANT B can only be viewed as a main picture. (Component: Y-PBPRinput can be viewed as sub-picture only when SPLIT PIP mode is selected.) To select between main picture and PIP sub-picture tuning, press the PIP CH button on the remote. The highlighted channel display will move with every press of the PIP CH button. When the top channel display is highlighted, channel tuning is for the main picture. When the lower channel display is highlighted, channel tuning is for the PIP sub-picture. This method of picture tuning is the same for one antenna input (ANT A only) and two antenna inputs (ANT A and ANT B).

The Picture-in-Picture feature is convenient when you want to watch more than one program at the same time. You can watch a TV program while viewing other programs from the ANT A source or any of the video inputs.

AUDIO OUT
+	-
SUB	L
WOOFER
L
R
+	-

R

REAR SPEAKER 8Ω ONLY

VCR
Back of
VCR	R L V
	OUTPUT

STOP

CONNECT ONLY 8 OHM SPEAKERS

DO NOT SHORT CIRCUIT

THESE TERMINALS

(Such damage is NOT COVERED by your television warranty)

COAXIAL OPTICAL

DIGITAL IN

Rear Panel of Television

					L	ANT A
					R
S-VIDEO		S-VIDEO		S-VIDEO	AUDIO	TO
					INPUT	CONVERTER
						PC 1
VIDEO	Y	VIDEO	Y	VIDEO
(MONO)	P B	(MONO)	P B	(MONO)		ANT B
L		L		L
R	P R	R	P R	R
AUDIO		AUDIO		AUDIO
VIDEO 1		VIDEO 2		MONITOR
				OUT

	MENU		EXIT
VOL		SELECT		CH
SVCS	MUTE		STATUS	D
				SCH
VCR
	PLUS	INFO	GUIDE/TV
	+
VID1		VID2		VID3
PIP		PIP CH		FREEZE	,
			PIP ACCESS
PIP MODE		SWAP
PROG		TV/VCR		SLOW

REC

RC5500DL

Use above connection to view VCR program as a sub-picture while viewing another program as a main picture (ANT A, ANT B, V:2 or V:3 input). You may also view the VCR program as a main picture while viewing another program as a sub-picture (ANT A, V:2 or V:3 input).

PIP button

Press the PIP button and a sub-picture will appear in one of the three different modes (SINGLE, SPLIT or SURF), depending on the last selection of the PIP mode. To change the PIP mode, use the PIP MODE button to cycle through the three different modes.

SINGLE MODE PIP

Press the PIP button and a sub-picture appears in one corner of the screen. Press the PIP button again to remove the sub-picture from the screen. Use the PIP CH button to select between main and sub-picture tuning control (indicated by highlighted channel display.) Press the VID1~VID3 button when sub-picture channel tuning is being controlled, to change between VIDEO: 1, VIDEO: 2, VIDEO: 3. Press ANT button to change to ANT A source. (ANT B source cannot be viewed as a sub-picture.)

PIP

Main Picture

PIP

Sub Picture

ANT A 10

SPLIT MODE PIP

When you press the “PIP” button, the main channel and the PIP sub-picture will appear at the center of the screen (main channel on left side and sub-picture on right side). Press the “PIP” button a second time to return to normal viewing. Use the PIP CH button to select between main and sub-picture tuning control (indicated by highlighted channel display). Press the VID1~VID3 button when sub-picture channel tuning is being controlled, to change between VIDEO:1, VIDEO:2, VIDEO:3. Press ANT button to change to ANT A source. (ANT B source cannot be viewed as a sub-picture).

PIP

PIP

NOTES: 1. Y-PBPRinput cannot be viewed as main picture or sub-picture when in SINGLE PIP MODE. If you tune to a Y-PBPRinput, the TV set will automatically change to SPLIT PIP MODE.

2.When ANT B is selected as the main channel, the SWAP feature is disabled.

3.COMPONENT: Y-PBPRinput can be viewed as main or sub-picture, only when SPLIT PIP MODE is chosen.

4.Only sound from the main picture can be heard.

5.It will take more than 3 seconds for the CPU to synchronize the motor frequency with input signal frequency when you change the VIDEO input mode (Video: 1, Video: 2 and so on), or press the TV/PC button to switch between TV, PC1 and PC2 modes.

28