Memorex MT2012 owner manual AUDIO/VIDEO Jack Connections, Setting Language

AUDIO/VIDEO JACK CONNECTIONS (CONTINUED)

4. To connect the TV to a VCR with an S-VIDEO jack

If you connect a VCR with an S-video jack to the S-VIDEO jack on the rear of TV, you must also connect the audio cables to the AUDIO IN jacks on the rear of the TV. The S-video cable only carries the video signal; the audio signal is separate.

VCR	Rear of TV
	AUDIO (L)
	AUDIO (R)

(not supplied)	S-VIDEO
(not supplied)

NOTE: When the S-video cable and the video cable are connected to each jack at the same time, the S-video cable takes precedence over the video cable.

ENGLISH

SETTING LANGUAGE

This TV can display the on-screen language in English, Spanish or French.

On-screen language selection (step 3) will automatically appear on the screen when you press the MENU button initially. Select the language you prefer first, then proceed with the other menu options.

1	Press the MENU button.		CH SETUP		3	Press the SET + or – button to select	LANGUAGE / IDIOMA / LANGUE
		MENU
			PICTURE			the desired language: English (ENGLISH),	ENGLISH
			STABLE SOUND ON	OFF		Spanish (ESPAÑOL) or French	ESPAÑOL
			LANGUAGE
2	Press the SET + or – button to		V-CHIP SET			(FRANCAIS), then press the ENTER	FRANCAIS
	select the LANGUAGE mode,	〈 + / — / ENTER / MENU 〉				button.	〈 + / – / ENTER / MENU 〉
	then press the ENTER button.
						Press the MENU button until the menu screen is cleared.
					4

NOTE:

If Spanish or French is chosen, the Closed Caption indicators will be in the selected language, but the Closed Caption text will not be affected by the language selection.

TV OPERATION

1	To turn on the TV, press the POWER button.
	The VOLUME can be adjusted to a desired level by
2
	pressing the VOL (VOLUME) or button.
	The sound level will be indicated on the TV screen by
	green bars and a number. As the sound level in-
	creases, so do the number of bars and the number on
	the screen. The same is true for decreasing the level.

3 Set the TV/CATV menu option to the appropriate position. When shipped from the factory, this menu option is in the CATV setting. See “MEMORIZING CHANNELS”.

TV	-	VHF/UHF channels
CATV	-	CABLE TV channels

4 CH (CHANNEL) and buttons

Press and release the CH (CHANNEL) or button. The channel automatically stops at the next channel set into memory. Press and hold the button down to change channels more quickly.

For proper operation, before selecting channels, they should be set into the TV's memory.

See “MEMORIZING CHANNELS”.

Direct Channel Selection buttons (0-9)

Press these buttons to select a channel. The channel number will appear on the upper right corner of the TV screen. If an invalid channel number is selected, the display will revert to the original channel.

TV Mode Direct Channel Selection

When the TV/CATV menu option is in the TV setting, all channels can be instantly selected by using two buttons. (For example, to select channel 2, press “0”, then “2”. If you press only “2”, channel selection will be delayed for a few seconds). For channels 10 and above, press the 2 digits in order.

CATV Mode Direct Channel Selection

When the TV/CATV menu option is in the CATV setting, channels can be selected as follows:

CH. 1-9 Press “0” twice, then 1-9 as needed. Example, to select channel 2, press “002”.

CH. 10-12 Press “0”, then remaining 2 digits. Example, to select channel 12, press “012”.

CH. 13-99 Press the 2 digits in order.

Example, to select channel 36, press “36”.

CH. 100-125 Press the 3 digits in order.

Example, to select channel 120, press “120”.

NOTE: If the station being viewed stops broadcasting, the TV will automatically shut off after 15 minutes.

7

3U10421A-E 7 1/21/05, 9:21 AM