PSTN Access Code
US/Canada where daylight saving time is applicable:
This means the daylight saving time starts from the first Sunday of April at 2AM and ends the last Sunday of October at 2AM. The saving is 60 minutes (1hour).
Default is “*00”, user can change it. By pressing the code user can switch the phone to PSTN line connected to the Line port of ATA and make PSTN outgoing calls. This is called PSTN Pass Through.
ADVANCED CONFIGURATION AND FXS PORTS PARAMETERS
To login to the Advanced Setting and FXS port configuration pages, administrator password is required. The default administrator password is “admin”. User can change the administrator password here. The password is case sensitive and the maximum length is 25 characters.
| TABLE 9: |
|
| ||
|
|
|
|
| |
| Admin Password | Administrator password. Only administrator can configure the “Advanced |
| ||
|
|
| Settings” page. Password field is purposely blanked for security reason after |
| |
|
|
| clicking update and saved. The maximum password length is 25 characters. |
| |
|
|
|
|
|
|
| Home NPA |
| Local area code for North American Dial Plan. |
|
|
|
|
|
|
| |
| Layer 3 QoS |
| This field defines the layer 3 QoS parameter which can be the value used for |
| |
|
|
| IP Precedence or |
|
|
|
|
|
|
| |
| Layer 2 QoS |
| Layer 2 QoS settings. Default setting is blank. Other VLAN supported |
| |
|
|
| equipments required if configured these settings. |
|
|
|
|
|
|
| |
| No Key Entry timeout |
| Default is 4 seconds. User can short or extend that depends on digits dialed |
| |
|
|
|
|
|
|
| STUN Server |
| IP address or Domain name of the STUN server. |
|
|
|
|
|
|
| |
|
|
| Default is 20 seconds. The interval of sending dummy UDP packet to keep |
| |
|
|
| NAT “pin hole” open. |
|
|
|
|
|
|
| |
| Use NAT IP |
| NAT IP address used in SIP/SDP message. Default is blank. |
| |
|
|
|
|
| |
| Firmware Upgrade and |
| Default method is HTTP. Firmware upgrade may take up to 10 minutes |
| |
| Provisioning |
| depending on network environment. Do not interrupt the firmware upgrading |
| |
|
|
| process. |
|
|
|
|
|
|
|
|
| Firmware Server Path |
| IP address or domain name of firmware server. |
|
|
|
|
|
|
|
|
| Config Server Path |
| IP address or domain name of configuration server. |
|
|
|
|
|
|
| |
| Firmware File Prefix |
| Default is blank. If configured, |
| |
|
|
| prefix. This setting is useful for ITSPs. End user should keep it blank. |
| |
|
|
|
|
|
|
| Firmware File Postfix |
| Default is blank. End user should keep it blank. |
|
|
|
|
|
|
|
|
| Config File Prefix |
| Default is blank. End user should keep it blank. |
|
|
|
|
|
|
|
|
| Config File Postfix |
| Default is blank. End user should keep it blank. |
|
|
|
|
|
|
|
|
| Automatic Upgrade |
| Default is “Yes”. |
|
|
|
|
|
|
| |
| Firmware Key |
| For firmware encryption. It should be 32 digit in Hexadecimal Representation. |
| |
|
|
| End user should keep it blank. |
|
|
|
|
|
|
|
|
| Caller ID Scheme |
| • Bellcore (North America) |
|
|
|
|
| • CID (Canada) |
|
|
|
|
| • DTMF (Brazil) |
|
|
|
|
| • DTMF (Sweden) |
|
|
|
|
| • DTMF (Denmark) |
|
|
|
|
|
|
|
|
| Grandstream Networks, Inc. |
| Page 21 of 34 |
| |
|
|
| Firmware 1.0.3.64 | Last Updated: 2/2007 |
|