Sony KP-41T65C service manual Operating a cable box or DBS receiver, Operating video equipment

– 20 –

MDP manufacturer code numbers

Manufacturer	Code number
Sony	701
Kenwood	707
Magnavox	703
Maranz	702
Mitsubishi	702
Panasonic	704
Philips	703
Pioneer	702
RCA	702
Sanyo	706
Sharp	705
Yamaha	703

Notes

•If more than one code number is listed, try entering them one by one, until you come to the correct code for your equipment.

•In some rare cases, you may not be able to operate your non- Sony video equipment with the supplied remote control. This is because your equipment may use a code that is not included with this remote control. In this case, please use the equipment’s own remote control unit.

•The code numbers for Sony equipment are assigned at the factory as follows:

VHS VCR	301	(preset code for the supplied
		remote control)
8 mm VCR	302
Beta, ED Beta VCRs	303

•Whenever you remove the batteries — to replace them, for example — if too much time is taken, the code number may revert to the factory setting and must be reset.

36-ENOperations

Operating video equipment

			VTR (POWER)
VTR (FUNCTION)
Video operating
buttons
1	2	3
4	5	6	0 – 9 buttons
7	8	9
	0		ENTER

CH +/–

Use the video operating buttons on the remote control to operate the video equipment.

Press VTR (FUNCTION) before operating the video equipment.

Operating a VCR	Buttons on the remote control
To turn on or off	Press VTR (POWER).
To select a channel	Press the 0 – 9 buttons.
directly
To change channels	Press CH +/–.
To record	Press ( while pressing r. First release
	(, then release r.
To play	Press (.
To stop	Press p.
To fast forward	Press ).
To rewind the tape	Press 0.
To pause	Press P.
	To resume normal playback, press again.
To search the picture	Press ) or 0 during playback.
forward or backward	To resume normal playback, release the
	button.
To change input mode	Press TV/VTR.

Operating an MDP	Buttons on the remote control
To turn on or off	Press VTR (POWER).
To play	Press (.
To stop	Press p.
To pause	Press P.
	To resume normal playback, press again.
To search the picture	Keep pressing ) or 0 during
forward or backward	playback.
	To resume normal playback, release the
	button.
To search the chapter	Press CH +/–.
forward and backward
N o t e

•If the video equipment does not have a certain function, the corresponding button on this remote control will not operate.

Operating a cable box or DBS receiver

You can program the supplied remote control to operate a cable box or DBS receiver. Follow the procedures below to set the manufacturer’s code number in the remote control.

			DBS/CABLE (POWER)
			DBS/CABLE
			(FUNCTION)
DISPLAY*
1	2	3
4	5	6	0 – 9 buttons
7	8	9
JUMP	0		ENTER
TV/DBS*			GUIDE*
			V/v/B/b/	*

MENU*

CH +/–

CODE SET

*The TV/DBS, GUIDE, DISPLAY, V/v/B/b/ , and MENU buttons can be used only with a DBS receiver.

1 Turn off the equipment you want to set up, and press DBS/CABLE (FUNCTION).

FUNCTION

DBS/CABLE

2 Press the CODE SET, DBS/CABLE (FUNCTION), and 0 – 9 buttons to enter the manufacturer’s code number (see the chart on the right column), then press ENTER. For example, to program your remote control to operate a Sony DBS receiver, press CODE SET, DBS/CABLE (FUNCTION), 8, 0, 1, and

ENTER.

FUNCTION		ENTER
CODE SET DBS/CABLE
	0	1
8

3 Press DBS/CABLE (POWER) to turn on the cable box or DBS receiver.

DBS/CABLE

4 Use the cable box/DBS control buttons to check if the code number works.

For example, to operate a cable box or DBS receiver, you can use the DBS/CABLE (POWER), JUMP, CH +/–, 0 – 9 and ENTER buttons.

N o t e

•If the cable box or DBS receiver does not have a certain function, the corresponding button on this remote control will not operate.

To operate the projection TV

Press TV (FUNCTION). Then use the projection TV control buttons to control the projection TV.

For more details on operating the cable box or DBS receiver

Refer to the operating instructions that come with the

equipment.EN

If the remote control doesn’t work

•First, try repeating the setup procedures using the other codes listed for your equipment.

Manufacturer code numbers (cable box)

Manufacturer	Code number
Hamlin/Regal	222, 223, 224, 225, 226
Jerrold/G. I.	201, 202, 203, 204, 205, 206, 207, 208,
	218
Oak	227, 228, 229
Panasonic	219, 220, 221
Pioneer	214, 215
Scientific Atlanta	209, 210, 211
Tocom	216, 217
Zenith	212, 213

Manufacturer code numbers (DBS receiver)

Manufacturer	Code number
Sony	801	(preset code for the supplied
		remote control)
RCA	802

Notes

•If more than one code number is listed, try entering them one by one until you come to the correct code for your equipment.

•If you enter a new code number, the code number you previously entered at that setting is erased.

•In some rare cases, your equipment may use a code that is not provided with this remote control and you may not be able to operate your equipment with the supplied remote control. In this case, use the equipment’s own remote control unit.

•Whenever you remove the batteries — to replace them, for example — if too much time is taken, the code numbers may revert to the factory setting and must be reset.

Operations 37-EN