RCA L42FHD28 warranty Programming the Remote, Using Direct Entry, Using Manual Code Search

Page 20

Using the Remote Control

Programming the Remote

ON•OFF

TV

PIP

SAT•AUX

DVD

GO BACK

VOL

CH

 

MUTE

 

INFO

MENU

+ CH CTRL

ZOOM-

ZOOM+

CLEAR

GUIDE

 

PRESETS

There are three ways to program the remote control to operate other devices: Direct Entry, Manual Code Search, and Automatic Code Search. If you have recently purchased the device you want to control or if the device has many codes, you might want to try the manual code search first.

Using Direct Entry

1.Turn on the device you want to control.

2.Look up the brand and code number(s) for the device in the code list at the end of this section.

?!+-

 

DEF

 

ABC

 

GHI

JKL

MNO

 

 

PQRS

TUV

WXYZ

INPUT

SUB CH

_,.:=$

You’ll use these darkened buttons for Direct Entry.

Using Manual Code Search

3.On your remote control, simultaneously press and hold the ON•OFF and MUTE buttons (approximately 3 seconds) until a device button remains lit. Then release the buttons.

4.Press and release the device button (SAT•AUX or DVD) you want to program.

5.Enter a three digit code from the code list.

6.To test the code you’ve programmed for that device button, point the remote at the device and then press ON•OFF to see if the device responds to the remote control.

If the device turns off, you’ve entered the correct programming code for your device. Circle the code you entered for future reference.

If the device doesn’t turn off, repeat these steps until you’ve tested all codes for your device’s brand or try to run a manual code search.

Note: Before using manual code search, you must use Direct Entry first. This lets the remote know which type of device to begin searching codes. Then proceed with the following steps.

1.Turn on the device you want to control.

2.On your remote control, simultaneously press and hold the ON•OFF and MUTE buttons (approximately 3 seconds) until a device button remains lit. Then release the buttons.

3.Press and release the device button (SAT•AUX or DVD) you want to program.

4.Repeatedly press and release the ON•OFF button, watching for the device to respond. If it does turn off, press and release the OK button within 3 seconds to save the code. If you accidentally passed the code before saving it, press the left arrow button to backtrack through the codes; then use the right arrow button to go forward through the codes again.

When all codes have been searched, the device button flashes 3 times, then the remote exits manual code search and returns to normal operation.

Using Automatic Code Search

1.Turn on the device you want to control.

2.On your remote control, simultaneously press and hold ON•OFF and MUTE (approximately 3 seconds) until a device button remains lit. Then release the buttons.

3.Press and release the device button you want to program.

continued on next page...

20

Chapter 2

Image 20
Contents LCD Users Guide Important Information Product Registration Product InformationImportant Safety Instructions O U N D C L a M P STable of Contents Things to Consider Before You Connect Connections and Setup Get the PictureGetting Channels What You NeedChoose Your Connection Jacks Used Cables Needed Go toVideo Basic Connection Component Video Advanced ConnectionViewing the Picture from the Connected Device Connecting the Device with Video BasicConnecting the Device with Component Video Advanced This is an example of a connection using the HDMI/DVI jack HDMI/DVI ConnectionConnecting the Device VGA Connection Viewing the PCHow to Use the Remote Control to Complete the Initial Setup Plug in the TVPut Batteries in the Remote Turn on the TVComplete the Initial Setup Complete Channel SetupSet the Signal Type Set the Menu LanguageChanging Channels What To ExpectWatching TV Explanation of Jacks in alphabetical order CMP2 Y Pb Pr Component Video Same as described forSide Panel Buttons Buttons and Other Jacks On Your TVSide Input Jacks Using the Remote Control Buttons on the Remote ControlUsing the Remote Control Using the Input ButtonProgramming the Remote to Operate Other Devices Find Out If You Need to Program the RemoteUsing Direct Entry Using Manual Code SearchUsing Automatic Code Search Programming the RemoteModes of Operation How to Use the Remote After You’ve Programmed ItVolume Punchthrough Feature Deleting ALL Volume Punchthrough Commands Cable Remote Code ListAudio Codes DVD/VCR Combo Codes DVR/DVD CombosDVR Codes DVR/Cable CombosVCR Codes Web TVAutotuning Channel BannerUsing the TV’s Features Lock/Unlock Parental Controls Parental Controls and V-ChipHow V-Chip Works for USA and Canada US V-Chip TV Ratings V-Chip Rating ScreenBlocking Age-Based Ratings Hierarchy of Age-Based RatingsBlocking Canadian V-Chip Ratings Blocking Specific Content ThemesContent Themes Chip Movie Rating Limit Block ChannelsFront Panel Block Blocking Unrated/Exempt ProgramsAdditional Features Future Rating RegionPicture Processing Screen FormatsSound Menu Using the Menu SystemChannel List Menu Using the TVs Menu System Sound Mode NormalPicture Menu PictureSetup Menu Advanced Picture Settings not available on VGAClosed caption Preferences Parental Control Menu Time MenuFrequently Asked Questions FAQs Other InformationTroubleshooting Other InformationButtons don’t work TV turns off unexpectedlyTV turns on unexpectedly Can’t select certain channelRating limits don’t work Don’t remember my password and I want to unlock the TVMounting Your TV to the Wall Canadian English V-Chip Rating System Chip Rating ExplanationsUS V-Chip Rating System Canadian French V-Chip Rating System Limited Warranty For how long after your purchaseCare and Cleaning How state law relates to warrantyFCC Information TTE Technology, IncWest 103rd Street Indianapolis, Tocom