RCA J32L637 manual What To Expect, Watching TV, Changing Channels

Page 11

Connections and Setup

Min Stdby Power  When enabled, keeps power consumption levels compliant with Energy Star standards. The TV is shipped with this enabled.

Legacy Mode  When turned on, allows the TV to work with earlier DSCI versions. Off is the default setting.

Info Menu  Allows the master user to determine whether the Channel Banner is displayed when the INFO button is pressed on the remote. Page 24 shows this display.

Hospital Mode When turned on, allows the TV to function with the hospital pendant remote. For more information about this remote, go to page 24.

Note: When Remote Config. and Front Panel are set to Disabled, the MENU button on the master remote turns on the TV.

A10 CBS

Look for the A at the bottom of the screen to make sure you're on the Analog Input.

D10-1 CBS

Look for the D at the bottom of the screen to make sure you're on the Digital Input.

What To Expect

Watching TV

•Remember: If you have an analog signal connected to your ANTENNA/CABLE ANALOG INPUT, then look for an A at the bottom of the screen to make sure you're tuned to the Analog input. Press the ANTENNA button if the A isn't appearing.

Analog video is sent in a 4/3 format, which your TV displays these channels in a 16/9 format. Press the LEFT/RIGHT ARROW button to view the different formats available. Go to page 24 for more explanation of screen formats.

•Remember: If you have a digital signal connected to your ANTENNA/CABLE DIGITAL INPUT, then look for a D at the bottom of the screen to make sure you're tuned to the Digital input. Press the ANTENNA button if the D isn't appearing.

Most digital video is sent in a 16/9 format which does fill your screen, but sometimes is sent in 4/3 which does not fill your screen. It depends on how the station or source device is formatting the video. If there are bars on-screen, press the LEFT/ RIGHT ARROW button to try a different format that may eliminate the bars. Go to page 24 for more explanation of screen formats.

Changing Channels

•Digital channels can have both primary channels (like the analog channel number) and sub-channels. First tune to the Digital Input by pressing the ANTENNA button and look for a D at the bottom of the screen. To tune to a digital channel with a sub-channel, enter the primary channel number, then press the right arrow button. Enter the sub-channel number and press OK.

•Depending upon the type of signals you have connected to your HDTV, you might notice that the channels change slower than you’re used to. This is perfectly normal. Digital cable channels sometimes take longer to tune.

Chapter 1

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents LCD Television User’s Guide Product Registration Product Information Important InformationRead these instructions Table of Contents Things to Consider Before You Connect Getting Regular Analog Channels Connections and SetupGet the Picture Getting Digital ChannelsStart-up Rear Jack PanelMaster Menus ClonePROUnderstanding the Menus Set the TimeSound Menu Using Master and Basic MenusSetting Limits in Master Menus Access and Power Options Menu Changing Channels What To ExpectWatching TV Explanation of Jacks in alphabetical order Front Panel Buttons Right Side Input Jacks when facing back of TVButtons and Other Jacks On Your TV Basic Remotes Types of Remote ControlsAdditional Remote Buttons R130K2 Master RemotesClonePRO Remote Buttons Using the Remote ControlPicture Menu Basic Menu SystemTime Menu Using the Menu SystemParental Control Menu Language & CC Menu Channel Banner Using the TVs FeaturesLock/Unlock Parental Controls Using the TV’s FeaturesParental Controls and V-Chip How V-Chip Works for USA and CanadaUS V-Chip TV Ratings Blocking Age-Based Ratings V-Chip Rating ScreenBlocking Canadian V-Chip Ratings Blocking Specific Content ThemesBlock Digital Channels Chip Movie Rating LimitBlocking Movie Ratings Block ChannelsAdditional Features Following formats are only available for analog video Other Information Frequently Asked Questions FAQsModes of operation Using the ClonePRODsci mode Other InformationIR red Buttons IR ModeCloning a TV ClonePRO TroubleshootingTV Problems TroubleshootingProblems with HDMI/DVI Connection Mounting Your TV to the Wall Remote Control Doesn’t WorkCanadian English V-Chip Rating System Chip Rating ExplanationsUS V-Chip Rating System Canadian French V-Chip Rating System How to Set Up the Autotuning Feature AutotuningWhat we will do within one year Limited WarrantyForth Above Care and CleaningTTE Technology, Inc FCC Information
Top Page Image Contents