Panasonic TC-L42U5X, PTAE8000U Installing the remote’s batteries First Time Setup, Remote control

	Installing the remote’s batteries						First Time Setup
						First time setup screen is displayed only when the TV is
			Close			turned on for the first time after the power cord is inserted
	Open					into a wall outlet and when “Auto power on” is set to “No”.
							Turn the TV On with the POWER button
	Push!
						 Configure your viewing mode
						1無	Select your language and viewing mode (Be sure to select
							“Home use”)
zz Incorrect installation may cause battery leakage and						2無 Please confirm your selection (Home Use) before pressing
							OK button.
	corrosion, resulting in damage to the remote control.
						zz If you use any other step other than “ Select your viewing
	zz Do not mix old and new batteries.						mode “ then turn the TV off, or if you used the EXIT button to
	zz Do not mix different battery types (such as alkaline and						quit before completing the settings, the next time you turn the
	manganese batteries).						TV on, “First time setup” will not be automatically displayed.
	zz Do not use rechargeable (Ni-Cd) batteries.						• The settings up to that point are saved.
zz Do not burn or break batteries.							• You can start “First time setup” from Setup menu of
							main menu at any time.
	Remote control					zz Language, ANT/Cable setup, Input labels, and Clock can also
							be changed in the Settings Menu.
1無 POWER - Turns the TV on						 Auto channel setup (ANT/Cable setup)
						1無	Select the connected Antenna in terminal.
	and off.
		1		11			Not used: Go to step 4 (Label inputs)
	LAST - Switches to previously
2無							Select “Not used” when no wire is connected to the
	viewed channel or input.						“Antenna/Cable” terminal.
3無	STILL - Still picture direct			12			zz Typical when a Cable/Satellite box is connected to a TV
	function key.						AV input.
4無	CC - Switches the Closed						zz Prevents accidental tuning to an unavailable signal, when
		2					Cable or Satellite box is used.
	Caption mode On or Off.			13
		3				2無	Select “Start”.
5無	INPUT - Select mode “ANT/	4		14			Skip: Go to step 4 (Label inputs)
	Cable in”, ”HDMI 1”, ”HDMI 2”,	5			15		Start scanning the channels (Available channels are
	”Component”, ”Video”, ”PC”						automatically set.)
	by pressing INPUT button of	6		16			Note:
	Remote Control.	7		17			zz This process may take up to 20 minutes.
6無	Volume Up / Down (VOL+						zz This step is not needed when a Cable or Satellite box is
		8		18			connected to an AV input.
	/ - ) - Press to decrease or					3無	Finished scanning. Completion message is displayed when
	increase the audio volume.
							the Auto program scan is successfully completed.
7無	MUTE - Turns off/on the						If there is no available channel, return to ANT/ Cable setup. “Not
	sound.	9		19			used” will be selected.
8無	FORMAT - To cycle through						zz Operation of the EXIT button during “First time setup”
	the aspect modes.			20			Press the button once to display confirmation screen.
9無	MENU - Press to display on-	10					Press again to close confirmation screen.
	screen menu.						[EXIT confirmation screen]
10無 PLAY / PAUSE / STOP -							Yes Exit “First time setup”
	Operation of media player.						No Return to the original screen.
11無 SAP - Selects Secondary						4無	Give names to the TV’s inputs (Label inputs)
	Audio Programming .						When done, select NEXT and press OK to go to the next step.
12無 Channel Numbers - Directly						Label: [BLANK] Not used/Blu-ray/DVD/DVD REC/HOME THTR/
	tune channels.						GAME/COMPUTER/VCR/CABLE/SATELLITE/DVR/
13無 SLEEP - Accesses the sleep timer.							CAMERA/MONITOR/AUX/RECEIVER/MEDIA CTR/
							MEDIA EXT/OTHER
14無 FAVORITE - Accesses the Favorites channel.							•Select “Not used” for any back-panel input that has
15無 USB - Viewing from USB.							no device connected to it. Afterward, the input will be
16無 Channel Up / Down (CH V / V) - Press to switch to the last or							skipped when pressing INPUT, for your convenience.
	next channel.						•The input labels can be changed at any time from the
							TV’s setup menu.
17無 EXIT - Exit from the menu screen.
						5無	Adjust the Clock (Set clock)
18無 INFO - Displays TV status information as well as program
	details.						When done, select NEXT and press OK to go to the next step.
						6無	Complete the First time setup.
19無 RETURN - Press to Return to previous menu.
							Congratulations! You are done.
20無 COLOR KEY - Red/Green/Blue/Yellow key for various
						The First time setup can be repeated at any time.
	function.
						Press MENU and select SETUP; then “First time setup”.
						To watch TV via a Cable box, Satellite receiver, or any
						other source (DVD, DVR, gaming device, etc.), press the
						INPUT button and select the appropriate input.

4