Panasonic TH-37PWD8UK, TH-50PHD8UK, TH-37PHD8UK manual PC Input Terminals connection, Connections

Page 10

Connections

PC Input Terminals connection

COMPUTER

Conversion adapter (if necessary)

AUDIO

PC IN

D-sub 15p

RGB

PC cable

Audio

Stereo plug

Connect a cable which matches

the audio output terminal on the computer.

Notes:

•Due to space limitations, occasionally you may have trouble connecting D-sub 15P cable with ferrite core to PC input Terminal.

•Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

•The display resolution is a maximum of 640 × 480 dots (TH-37PWD8UK, TH-42PWD8UK), 768 × 720 dots (TH-37PHD8UK), 768 × 768 dots (TH-42PHD8UK), 1,024 × 768 dots (TH-50PHD8UK) when the aspect mode is set to “NORMAL”, and 852

×480 dots (TH-37PWD8UK, TH-42PWD8UK), 1,024 × 720 dots (TH-37PHD8UK), 1,024 × 768 dots (TH-42PHD8UK), 1,366 × 768 dots (TH-50PHD8UK) when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible to show ﬁne detail with sufﬁcient clarity.

•The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you will need to make setting changes to the computer at the time of connection.

•Some PC models cannot be connected to the set.

•There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminal.

•The computer shown in the illustration is for example purposes only.

•Additional equipment and cables shown are not supplied with this set.

•Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the speciﬁed frequency range.

•Component Input is possible with the pin 1, 2, 3 of the D-sub 15P Connector.

Signal Names for D-sub 15P Connector

11 12 13 14 15

6 7 8 9 10

1 2 3 4 5

Pin Layout for PC Input Terminal

Pin No.	Signal Name	Pin No.	Signal Name	Pin No.	Signal Name
1	R (PR/CR)	6	GND (Ground)	11	GND (Ground)
2	G (Y)	7	GND (Ground)	12	SDA
3	B (PB/CB)	8	GND (Ground)	13	HD/SYNC
4	GND (Ground)	9	NC (not connected)	14	VD
5	GND (Ground)	10	GND (Ground)	15	SCL

10

Image 10

Contents TH-42PWD8UK High Deﬁnition Plasma DisplayTH-42PHD8UK TH-50PHD8UK Risk of Electric Shock Do not Open Important Safety Instructions Table of Contents Canadian Notice FCC CautionTrademark Credits Safety Precautions When using the Plasma DisplaySetup MaintenanceSafety Precautions / Maintenance AC Power Supply CordAccessories Supplied AccessoriesRemote Control Batteries AC cord ﬁxing ConnectionsSpeakers COMPONENT/RGBPC Input Terminals connection Signal Names for D-sub 15P ConnectorConnections Communication parameters CommandSerial Terminals connection Basic format for control dataRGB signal R, G, B, HD, VD AV & Component connectionConnecting the AC cord plug to the Plasma Display Power on / OFFConnecting the plug to the Wall Outlet Basic Controls OFFBasic Controls On-Screen Menu Displays On Time / Power OFF Time / Power OFF TimeOn-Screen Menu Displays Initial selections Selecting the input signalSelecting the On-Screen Menu Language Normal Zoom Full Aspect ControlsNormal Full Clock Phase Adjusting POS. /SIZEClock Phase RGB/PC in modeUnder main Picture and sub picture display, select Press to select the input modePress to swap main picture and sub picture Picture which you would like to change input ModesSub screen Advanced PIPMain screen Dynamic Picture AdjustmentsStandard CinemaAdvanced Settings Picture AdjustmentsSound Adjustment MuteDigital Zoom Remote control UnitVOL button Mute button Surround button OFF Timer button Display the Operation GuidePresent Time Setup Press to set up Present Time of DAYDisplay the SET UP Timer Screen Press to select SET UP TimerPower on Time / Power OFF Time Screensaver For preventing after-images Mode selectionStart setting Negative / Scroll selectionReduces screen after-image Setup of Screensaver TimeScreensaver For preventing after-images OFF Dark MID Bright Side BAR AdjustPress to exit from Screensaver Customizing the Input labels Reduces power consumptionPower Save Standby Save Power Management Auto Power OFF Press to select on or OFF On OffSET UP for Multi Display How to setup Multi DisplayOption F for Multi Display SET UP for Multi DisplayDisplay Number locations for each arrangement ID remote control button operation ID Remote Control FunctionID Cancellation 3D Y/C Filter For Ntsc AV images SET UP for Input SignalsComponent / RGB in Select Component RGBPulldown / Video NR SET UP for Input SignalsColor System / Panasonic Auto Color SystemFREQ. kHz / V-FREQ. Hz Setting RGB sync signalSync Displays the H Horizontal / V Vertical frequenciesMENU&ENTER Options AdjustmentsMenu & Enter Off On Options AdjustmentsOff PC INPUT1 INPUT2 INPUT3 On OffOffOn Adjusts the image display size on screenSets the panel ID Control NormalizationShipping condition Troubleshooting Plasma Display panelPAL60 VIDEO/COMPONENT/RGB/PC input signalsVideo input RGBSpeciﬁcations TH-37PWD8UK TH-42PWD8UKSpeciﬁcations TH-37PHD8UK TH-42PHD8UKTH-50PHD8UK Executive Ofﬁce Customer’s RecordPanasonic Broadcast & Television Systems Company Panasonic Canada Inc