Panasonic TH-103PF9UK manual PC Input Terminals connection, Connections

Page 10

Connections

PC Input Terminals connection

COMPUTER

Conversion adapter (if necessary)

RGB

AUDIO

PC IN

Mini D-sub 15p

PC cable

Audio

Stereo plug

Connect a cable which matches

the audio output terminal on the computer.

Notes:

•Due to space limitations, occasionally you may have trouble connecting Mini D-sub 15P cable with ferrite core to PC input Terminal.

•Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

•The display resolution is a maximum of 1,440 × 1,080 dots when the aspect mode is set to “NORMAL”, and 1,920 × 1,080 dots when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible to show ﬁne detail with sufﬁcient clarity.

•The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you will need to make setting changes to the computer at the time of connection.

•Some PC models cannot be connected to the set.

•There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.

•The computer shown in the illustration is for example purposes only.

•Additional equipment and cables shown are not supplied with this set.

•Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the speciﬁed frequency range.

•Component Input is possible with the pin 1, 2, 3 of the D-sub 15P Connector.

•Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “COMPONENT” (when COMPONENT connection) or “RGB” (when RGB signal connection). (see page 37)

Signal Names for Mini D-sub 15P Connector

5 4 3 2 1

10		9		8	7	6
15	14		13	12		11

Pin Layout for PC Input Terminal

Pin No.	Signal Name	Pin No.	Signal Name	Pin No.	Signal Name
1	R (PR/CR)	6	GND (Ground)	11	NC (not connected)
2	G (Y)	7	GND (Ground)	12	SDA
3	B (PB/CB)	8	GND (Ground)	13	HD/SYNC
4	NC (not connected)	9	NC (not connected)	14	VD
5	GND (Ground)	10	GND (Ground)	15	SCL

10

Image 10

Contents Model No. TH-103PF9UK High Deﬁnition Plasma DisplayOperating Instructions EnglishRisk of Electric Shock Do not Open Important Safety Instructions Table of Contents Canadian Notice FCC CautionTrademark Credits When using the Plasma Display Safety PrecautionsTake steps to prevent toppling Setup MaintenanceSafety Precautions / Maintenance AC Power Supply CordAccessories Supplied AccessoriesRemote Control Batteries Close ConnectionsAudio OUT Terminals connection OpenPC Input Terminals connection Signal Names for Mini D-sub 15P ConnectorConnections Communication parameters CommandSerial Terminals connection Basic format for control dataSignal Name Component / RGB connection & RGB signal R, G, BDVI-D Input Connector DVI-D connectionConnecting the plug to the Wall Outlet Power on / OFFConnecting the AC cord plug to the Plasma Display Right side surfaceBasic Controls On OFFBasic Controls Right side Advanced SettingsOn-Screen Menu Displays Sound POS. /SIZEPower on Time Power OFF Time On-Screen Menu DisplaysSelecting the On-Screen Menu Language Selecting the input signalInitial selections INPUT1 INPUT2 INPUT3 PCNormal Zoom Full Mode Picture ExplanationAspect Controls Normal FullPress to adjust POS. /SIZE Adjusting POS. /SIZESize / DOT Clock / Clock Phase / 11 Pixel Mode During COMPONENT, RGB and PC input signalPOS Adjusting POS. /SIZEClock Phase SizeUnder main Picture and sub picture display, select Picture which you would like to change input modesAdvanced PIP Sub screen Main screenDynamic Picture AdjustmentsStandard CinemaAdvanced Settings Picture AdjustmentsSound Adjustment MuteSelect the magniﬁcation required for the enlarged display Digital ZoomDisplay the Operation Guide Return to normal display quit Digital ZoomPress to set up Present Time of DAY Present Time SetupPress to select Set Power on Time / Power OFF Time SET UP TimerDisplay the SET UP Timer Screen Press to select Press to select Power on FunctionScreensaver For preventing after-images Mode selectionStart setting Negative / Scroll selectionReduces screen after-image Setup of Screensaver TimePress to display the SET UP menu Screensaver For preventing after-imagesOFF Dark MID Bright Side BAR AdjustPress to exit from Screensaver Customizing the Input labels Reduces power consumptionAddition sign Selected Input Group of 4 2 × Group of 9 3 × Group of 16 4 × SET UP for Multi DisplayHow to setup Multi Display Press to select on or OFFPress to select OFF, on SET UP for Multi DisplayPress to select Seam Hides Video Display Number locations for each arrangement ExamplesID remote control button operation Seam Hides Video SettingID Remote Control Function ID Cancellation3D Y/C Filter For Ntsc AV images SET UP for Input SignalsComponent / RGB in Select Component RGBPulldown / Video NR SET UP for Input SignalsColor System / Panasonic Auto Color SystemFREQ. kHz / V-FREQ. Hz Setting RGB sync signalSync Displays the H Horizontal / V Vertical frequenciesOptions Adjustments Options Adjustments Off User1 User2 User3 Remocon NormalizationLocks Buttons on bottom face of main unit User1You can only useShipping condition Symptoms Check TroubleshootingSymptoms Checks Plasma Display panelDVI-D/COMPONENT/RGB/PC input signals DVI-D∗3Speciﬁcations Memo Executive Ofﬁce Customer’s RecordPanasonic Broadcast & Television Systems Company Panasonic Canada Inc