Jensen VM9412 Pre-installation, Wiring, Final Installation, Final ISO-DIN Installation

Page 9

VM9412

INSTALLATION

Pre-installation

1.Press the metal levers on both sides to remove the half- sleeve from the radio.

PREPARE RADIO

2.Install the half-sleeve.

a.Install adapter if necessary (optional).

b.Install half-sleeve into adapter or dashboard (use only the supplied screws). Do not force the sleeve into the opening or cause it to bend or bow.

c.Locate the series of bend-tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary so that the sleeve is firmly secured to the dashboard.

d.Install support strap to make the unit more stable.

INSTALL HALF SLEEVE

CAUTION! Be careful not to damage the car wiring.

3.Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve.

Wiring

Complete wiring as illustrated in the wiring diagram on page

3.Once the wiring is complete, reconnect the battery negative terminal. If there is no ACC available, connect the ACC lead to the power supply with a switch.

NOTE: When replacing a fuse, be sure to use correct type and amperage to avoid damaging the radio. The VM9412 uses one 10 amp mini-ATM fuse, located in the black filter box in-line with the main wire harness.

Final Installation

After completing the wiring connections, turn the unit on to confirm operation (ignition switch must be on). If unit does not operate, recheck all wiring until problem is corrected. Once proper operation is achieved, turn off the ignition switch and proceed with final mounting of the chassis.

1.Connect wiring adapter to existing wiring harness.

2.Connect antenna lead.

3.Carefully slide the radio into the half-sleeve, making sure it is right-side-up, until it is fully seated and the spring clips lock it into place.

NOTE: For proper operation of the CD/DVD player, the chassis must be mounted within 20° of horizontal. Make sure the unit is mounted within this limitation.

4.Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw and hex nut provided. Bend the strap to position it as necessary.

CAUTION! The rear of the radio must be supported with the strap to prevent damage to the dashboard from the weight of the radio or improper operation due to vibration.

5.Replace any items you removed from the dashboard.

FINAL INSTALLATION

 

5

4

 

1

 

 

2

 

3

Final ISO-DIN Installation

1.Remove trim ring.

2.Mount factory brackets on new radio using existing screws from old radio.

3.Slide radio chassis into dash opening and secure.

4.Reinstall dash panel.

FINAL ISO-DIN INSTALLATION

3

2

1

4

5

Image 9 Jensen VM9412 operation manual Pre-installation, Wiring, Final Installation, Final ISO-DIN Installation
Contents VM9412 Band AS Page Contents Page Preparation FeaturesDisconnecting the Battery Optional AccessoriesOptional Equipment Tools and SuppliesWiring Diagram To Head Unit Pre-installation InstallationWiring Final InstallationService at 1-800-323-4815 for assistance ANTI-THEFT FeatureButton Operation Controls and IndicatorsRight joystick Pause/Play/EnterUp joystick TFT Display RearRemote Control Preset PowerMenu TitlePIC SetupOpen CloseUsing the TFT Monitor Parking Brake Parameter Adjustment ProcedureMonitor Movement Mechanism Parking Brake InhibitOperating Instructions MULTI-ZONE Operation Connecting the Rear Zone Touch ScreenChanging the Rear Zone Source Turning the Rear Screen OffAccessing Menu Items Setup MenuAdjusting a Feature Setting Options FunctionExiting the System Setup Menu Tuner Operation Preview Scan PS Auto Store ASLocal Radio Station Seeking LOC Recalling a StationSatellite Radio Operation Category Guide Mode DVD/VCD Video Operation Zooming Direct Chapter / Track SelectionMulti-Language Discs DVD Only Viewing an Alternate Picture Angle DVD OnlyGeneral Disc Information Symbol MeaningSymb 12cm Disc Properties Max Play Time MpegDVD/CD Audio Operation CD Player User InterfaceDirect Track Entry MP3/iPod User Interface MP3/WMA Media and File RequirementsMP3 Format Compatibility MP3 Playing OrderControlling your iPod Controlling MP3/WMA Disc PlaybackDirect Track/File Entry Problem Cause Corrective Action TroubleshootingTFT Monitor TunerError Messages Message Displayed Cause Corrective ActionMP3 Care and Maintenance Specifications Do not Return this Product to the Store Limited Warranty