TV Operation and Settings, Initial SET UP

TV SECTION

TV OPERATION AND SETTINGS

INITIAL SET UP

When you turn on the power for the first time, TV the INITIAL LANGUAGE screen is displayed. Select the language for screen display and perform auto programming of the channels.

1After antenna or cable connection is completed, connect the power cord into

a standard AC outlet.

2Press [STANDBY-ONy] to turn on the unit.

WATCHING A TV PROGRAM

1Press [STANDBY-ONy]to turn on the unit. TV

NOTES:	- HELPFUL HINTS -
If the TV screen shows snow	THE ANTENNA/CABLE/
	1.PLEASE CHECK TO SEE IF
noise and there is no operation	SATELLITE IS
noise and there is no operation	PROPERLY CONNECTED.
for more than 10 seconds,	2.DID YOU PERFORM
for more than 10 seconds,	“AUTO CH PROGRAMMING”?
	3.PLEASE REFER TO FRONT
“HELPFUL HINTS” appears.	PAGE OF THE OWNER’S
“HELPFUL HINTS” appears.	MANUAL OR REAR PANEL
	FOR SUPPORT LINE
	INFORMATION.

• Make sure if the antenna or cable is connected

properly. (Refer to “ANTENNA/CABLE CONNEC-

TIONS on page 6.)

• Set the“AUTO CH PROGRAMMING” in the

TV SECTION

SETTINGS

3Press one of the keys listed below to select the language of on-screen menu.

•ENGLISH: [VOL. Y]

•ESPAÑOL: [VOL. X]

•FRANÇAIS: [CH. K]

SELECT LANGUAGE

ENGLISH

NEXT:PRESS VOLYH

ESPAÑOL DESPUÉS:PRESIONE VOLXH

FRANÇAIS APRÈS:PRESSEZ CH.KH

CHANNEL SET UP. (Refer to “CHANNEL SET UP”

on page 11.)

• If those setting do not work properly, please

call our help line on the front page of this owner’s

manual.

2Use [CH. K / L] or the Number buttons to select your desired channel number.

OPERATION AND

4 Confirm the antenna (or cable)	– INITIAL SETUP –
connection and press [PLAY B].	PLEASE CONNECT ANTENNA
	OR CABLE OR SATELLITE
• The tuner scans and	TO THIS UNIT.
• The tuner scans and	IN ORDER TO PERFORM
	THEN PRESS PLAY,
memorizes all active	“AUTO CH PROGRAMMING”
memorizes all active
channels in your area.

5 When the scanning is completed,	CH 15
the tuner stops on the lowest
memorized channel.	(Example)
	(Example)

NOTES:

•You can exit the INITIAL SETUP menu by pressing [SET-UP]. If the button is pressed during channel scanning, the tuner stops scanning and the lowest memorized channel is displayed.

•The INITIAL SETUP menu is displayed every time you turn on the unit unless the scanning is com- pleted.

•In case no channel can be received by the channel scanning,

"NO TV SIGNALS" is displayed on	NO TV SIGNALS
the screen. Turn off the unit and
check the antenna connection,
then follow steps 1 to 5 again.

•You can change the setting after completing INI- TIAL SETUP by LANGUAGE menu or CHANNEL SET UP menu. (Refer to "ON-SCREEN MENU LAN- GUAGE" or "CHANNEL SET UP" on page 11).

To use the number buttons

•Single digit channels: (Ex. 02, 03, 04 and so on) Press [0] first to select a single digit channel.

•Two digit channels: (Ex. 12, 38, 95 ...) Press two digits directly.

•Tree digit channels: (Ex. 115, 125 ...)

Press [+100] first, then press the last two digits.

3 Use [VOL. X / Y] to adjust the volume.

	Press [MUTE] to instantly
	mute the sound. Press it again	VOLUME 20
	to restore the previous sound	VOLUME 20
		C C C C C C C C C C C C C C C C

	level.

NOTE:

•Even if you turn off the unit in the DVD mode, the unit will be in the TV mode when you turn it on again.

TO WATCH CABLE OR SATELLITE CHANNEL

If the unit is connected to a cable box or satellite box, use [CH. K / L] to select CH3 or CH4 accord- ing to the output channel setting of the device and select desired channel on that device.

TO WATCH EXTERNAL INPUT

When an external equipment is

connected to the front AUDIO/AUX VIDEO input jacks, press

[SELECT] or [CH. K / L] repeat- edly until "AUX" appears on the screen.

TV SECTION