CD Play

Use compact discs bearing the symbol shown. In addition to conventional 12 cm CDs, this system can be used to play 8 cm CDs without an adapter.

-This unit can play back the CD-R/RW that have recorded music data as well. However, some CD-R/RWs cannot be played back depending on the recording conditions.

-The CD-R/RW cannot be recorded in this unit.

1.Press the FUNCTION button to select CD function.

2.Press the OPEN/CLOSE button, disc tray slides out, “OPEN” appears.

3.Place the disc with the label fac-

ing up on the disc tray. (Place only one disc at a time.)

4. Press the OPEN/CLOSE button again to close the disc tray. “CLOSE” appears briefly, then the total number of tracks and the to- tal playing time on the disc appears.

5. Press the ibutton. Play starts from the first track. The current track number and elapsed playing time are displayed.

6.Press the n button to end disc play. When the last track has been played, the player stops automatically.

Note:

-If the disc is loaded with the label side downward, or if a badly scratched disc is loaded, “NO DISC” or “UNDISC” appears on the display. If this occurs, load the disc correctly or replace the damaged disc.

Notes on handling compact discs

- Do not expose the disc to direct sunlight, high humidity or high tem- peratures for extended periods of time.

-Discs should be returned to their cases after use.

-Do not apply paper or write anything on the disc surface.

-Handle the disc by its edge. Do not touch the playing surface (glossy side).

-Fingerprints and dust should be carefully wiped off the playing sur- face of the disc with a soft cloth.

Wipe in a straight motion from the centre to the outside of the disc.

-Never use chemicals such as record cleaning sprays, antistatic sprays or fluids, benzene or thinner to clean compact discs.

To start play from the desired track

Select the track by using the f or e button, then press the i but- ton.

Using the remote control

For normal music CD:

Press two number buttons within 4 seconds.

Example:

To select No. 3, press 0, 3.

To select No.10, press 1, 0.

To select No. 32, press 3, 2.

For MP3 CD:

Press three number buttons within 4 seconds.

Example:

To select No. 3, press 0, 0, 3.

To select No. 10, press 0, 1, then 0.

To select No. 125, press 1, 2, then 5.

Temporarily stopping play

Press the i button. To resume play, press the i button again.

Skip play

To skip to track 6 while track 3 is playing, press the e button repeatedly until “6” appears (in the track section) on the display. To skip back to track 3 while track 6 is playing, press the f button repeatedly until “3” appears.

-The number buttons on the remote control can also be used for skip play. To skip to track 6 while one track is playing, press 0, then 6 (for normal music CD), or 0, 0, 6 (for MP3 CD).

Search play (forward/reverse)

If the f or e button is pressed during play, the player will search at high speed in the forward or reverse direction while the button is being pressed. When the button is released, normal play will continue.

Repeat play

Press the REPEAT button (or the FM MODE/REPEAT button on the re- mote control) before or during play. Press the button once, “1 REPEAT” displays, repeat single track. Press the button twice, “ALL REPEAT” keeps displaying, the unit will repeat all tracks or all programmed tracks.

To cancel repeat play, press this button again till “1 REPEAT” or “ALL REPEAT” disappears.

Random play (Main unit only)

Press the RANDOM button, the player will automatically play disc option- ally, “RANDOM” will appear on the display screen.

Note:

-Press the n button to cancel random play.

-Random play will not function during programme play.

-If chosen random play when using MP3 disc, folder select function can’t work.

Programmed play

Up to 24 tracks on a disc can be programmed for play in any order.

-First, select CD function and load a disc that you want to programme.

-The tracks must be programmed in the stop mode.

-The same track can be programmed more than once.

1. Press the MEMORY button in the stop mode, “PROGRAM” appears and blinks.

2. Press the f or e button to se- lect a track.

-The number buttons on the remote control can also be used. In this example, press 0, 6.

3.Press the MEMORY button.

4. Repeat steps 2 - 3 above to pro- gramme additional tracks.

5. Press the i button to start pro- grammed play.

- When all programmed tracks have been played, the player stops au- tomatically.

-The programme contents are retained in memory.

-Any attempt to programme more than 24 tracks will result in “FULL” being displayed and discontinuation of the programming.

-The programme contents are retained even if the function selection is changed. Press the MEMORY button after selecting CD function, the programmed contents appear.

Checking the programme

Each time the MEMORY button is pressed in the stop mode, the pro- grammed details sequentially appear on the display.

-5-