Sharp PN-E471R manual Controlling the Monitor with a PC LAN To set from a PC, Default Gateway 0.0

Page 30

Controlling the Monitor with a PC (LAN)

■ To set from a PC

When the monitor is connected to a PC, LAN settings can be configured via PC.

Set up process

(1)Connect your monitor to a PC

(2)Specify the PC’s IP address

(3)Configure the monitor’s LAN settings

(1) Connecting your monitor to a PC

Connect a commercially available crossover LAN cable (UPT cable, Category 5) to the LAN port on the PC and this monitor.

LAN terminal

PC

To LAN terminal

LAN cable (commercially available, crossover)

(2) Specifying the PC’s IP address

To configure the monitor’s LAN settings, you must temporarily change the settings on the PC.

This explanation is based on Windows XP.

1.Log on to the PC with an administrator account.

2.Click [Start], and then click “Control Panel”.

3.Click “Network and Internet Connections”, and then click “Network Connections”.

If you are using the classic display style, double-click on

“Network Connections”.

4.Right click on “Local Area Connection” and from the menu, click “Properties”.

5.Click “Internet Protocol (TCP/IP)”, and then click “Properties”.

6.Make a note of the current IP address, subnet mask, and default gateway settings.

Make sure you write this information now as you will be changing the IP address, subnet mask, and default gateway settings back to these settings afterwards.

7.Temporarily change the IP address and subnet mask.

To access the monitor as it is shipped from the factory, set as follows.

•IP Address: 192.168.150.3

•Subnet Mask: 255.255.255.0

•Default Gateway: (leave blank)

8. Click [OK] and then reboot the PC.

TIPS

• This monitor is factory preset as shown below.

IP Address	: 192.168.150.2
Subnet Mask	: 255.255.255.0
Default Gateway	: 0.0.0.0

(3)Configuring the monitor’s LAN settings

Access the monitor using Internet Explorer.

Controlling the monitor

1.Turn the power ON to the monitor.

2.Set RS-232C/LAN SELECT on the SETUP menu to LAN.

PC operation

3.Launch Internet Explorer, in the “Address” box type “http://192.168.150.2/” and press the Enter key.

You will be prompted to enter a user name and password.

4.Leave the user name and password boxes blank and click [OK].

E30

Image 30

Contents PN-E471R PN-E421 Contents Part Names NFront viewNRear view Mode button See Size button See Menu button See Part Names NRemote control unitSignal transmitter Power button Display button See Mute button SeeMute Basic OperationDisplay MenuDot by Dot Basic Operation NSwitching the screen sizeWide Zoom Normal Cut offNExample of operation Menu ItemsDisplaying the menu screen NMenu screen displayMenu Items Baud Rate LAN Setup Speaker Select Option DC OUT SettingList of menu items Menu PN-ZB01 optional Not attached AttachedPIP/PbyP Some items may not be displayed depending on the input modeLines PbyP2 POSMenu item details NSCREENNPICTURE NSETUP 11 ENAUDIO Menu Items NOPTION NENLARGE PC input13 E NPIP/PbyPMenu Items NDual screen display Menu Items NEnlarge NZOOM2 Special SettingSetting procedure Enlarge menu, set Enlarge H/V and ENLARGE-POS H/V. SeeNSCHEDULE Power15 E DAY of the WeekAdjustments for PC screen display NAutomatic adjustmentNScreen display for adjustment 17 E PC connection Communication procedureControlling the Monitor with a PC RS-232C Communication conditions19 E NCommunication intervalNID numbers VOLM0020 ← 002VOLM0030 OK 002 IDLK0000 ← Wait ← OK 002 ← VOLM0010 OK 001 ←Setting of the Gamma user data 21 EHow to read the command table RS-232C command tablePower control/Input mode selection Controlling the Monitor with a PC RS-232C23 E Controlling the Monitor with a PC RS-232C Picture menuAudio menu Controlling the Monitor with a PC RS-232C Setup menu 25 E Controlling the Monitor with a PC RS-232C Option menuImage Position Epos setting Horizontal orientation Vertical orientationInitialization/Functional Restriction Setting Function menu 27 EControlling the Monitor with a PC RS-232C PIP/PbyP menu Commands for setting of the Gamma user data Controlling the Monitor with a PC RS-232C Others29 E Settings to connect to a LANControlling the Monitor with a PC LAN To set on the monitorThis monitor is factory preset as shown below IP Address Default Gateway 0.0Controlling the Monitor with a PC LAN To set from a PC Controlling the Monitor with a PC LAN 31 EControlling with a PC Basic operationMonitor’s menu Setup SeeInformation about this monitor appears Screen SeeDNS Server User Name / Password33 E Accept IP AddressAccount Name / Password Installation Information NAME/LOCATIONAuthentication Monitor NameCondition 35 ERecipient E-MAIL Addresses ConfirmationTrap When Authentication Fails Snmp SettingTrap Setting VersionTroubleshooting 37 EVesa DDC2B SpecificationsNProduct Specifications Vesa DPMS, DVI DmpmNDimensional Drawings Specifications39 E Specifications NPower management Dmpm Digital Monitor Power ManagementNDDC plug and play Specifications NCompatible signal timing PC NCompatible signal timing AV41 E NPC/AV DVI-D output terminal pins Specifications NPC/AV DVI-D input terminal pinsNPC D-sub input terminal pins NPC/AV Hdmi input terminal pinsPN-E471RE421 G EN10G1