Sharp LC 32SB27U operation manual Precautions when transporting the TV

Page 5

IMPORTANT SAFETY INSTRUCTIONS

Outdoor Antenna Grounding — If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

 

 

ANTENNA

 

 

LEAD IN WIRE

 

GROUND

ANTENNA

 

CLAMP

 

DISCHARGE UNIT

 

 

(NEC SECTION 810-20)

ELECTRIC

 

 

SERVICE

 

GROUNDING

EQUIPMENT

 

CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC — NATIONAL ELECTRICAL CODE

• Turn off the main power and unplug the AC cord from the wall outlet before handling.

• Use a soft cloth and gently wipe the surface of the display panel. Using a hard cloth may scratch the panel surface.

• Use a soft damp cloth to gently wipe the panel when it is really dirty. (It may scratch the panel surface when wiped strongly.)

If the panel is dusty, use an anti-static brush, which is commercially available, to clean it.

To protect the panel, do not use a dirty cloth, liquid cleaners or chemical cloth to clean it, such materials may damage the panel surface.

To clean the outer cabinet, use the same method. Do not use liquid or aerosol cleaners.

Water and Moisture — Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

Stand — Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart, stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product on a wall, be sure to follow the manufacturer's instructions. Use only the mounting hardware recommended by the manufacturer.

Selecting the location — Select a place with no direct sunlight and good ventilation.

Ventilation — The vents and other openings in the cabinet are designed for ventilation. Do not cover or block these vents and openings since insuffi cient ventilation can cause overheating and/or shorten the life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer's instructions are followed.

The Liquid Crystal panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the panel breaks.

Heat — The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifi ers) that produce heat.

The Liquid Crystal panel is a very high technology product with 1,049,088 pixels, giving you fi ne picture details. Occasionally, a few non-active pixels may appear on the screen as a fi xed point of blue, green or red. Please note that this does not affect the performance of your product.

Lightning — For added protection for this television equipment during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to the equipment due to lightning and power-line surges.

Power Lines — An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

To prevent fi re, never place any type of candle or fl ames on the top or near the TV set.

To prevent fi re or shock hazard, do not place the AC cord under the TV set or other heavy items.

• Do not display a still picture for a long time, as this could cause an afterimage to remain.

• To prevent fi re or shock hazard, do not expose this product to dripping or splashing. No objects fi lled with liquids, such as vases, should be placed on the product.

Do not insert foreign objects into the product. Inserting objects in the air vents or other openings may result in fi re or electric shock. Exercise special caution when using the product around children.

Precautions when transporting the TV

When transporting the TV, never carry it by holding or otherwise putting pressure onto the display. Be sure to always carry the TV by two people holding it with two hands — one hand on each side of the TV.

5

Image 5
Contents LC-32SB27U Supplied Accessories09P03-MX-NM For connectionsImportant Information Dear Sharp Customer Additional Safety InformationPrecautions when transporting the TV Child Safety Using an optional bracket to mount the TV Setting the TV on the WallAbout setting the TV angle Attaching/Detaching the StandPower indicator on the front of the television lights Green Using the Remote Control UnitConnecting Antenna Cable Installing Batteries in the Remote Control UnitPreparation AntennasTV Front Part NamesTV Rear/Side Input buttonConnecting a PC Connecting to External EquipmentWatching TV Turning On/Off the PowerInitial Setup Sleep Timer Changing VolumeDirect Button Operation Changing ChannelsDigital broadcasting audio mode MTS/SAP stereo modeDirect Button Operation ExamplePress Input again or press a/b to select the input source Press InputPress CC Operating On-Screen Display MenuFor PC input mode Press View ModeYou can select the screen size For HD programsUsing the control panel of the main unit Using the remote controlOn-Screen Display Menu On-Screen Display Menu OperationPicture Menu Advanced Picture SettingOPC Setting Audio Menu Power Control MenuEZ Setup Setup MenuCH Setup Input SkipPosition PC SetupPC Audio Select Hdmi Auto ViewReset Audio SetupParental Ctrl Parental Control Setting LanguageOn-Screen Display Menu Mpaa Voluntary movie rating system When setting an individual content-based rating itemTV Parental Guidelines RatingCanadian English Ratings How to temporarily release the V-CHIP BlockCanadian French Ratings Reactivating the temporarily released V-CHIP BlockOption Menu Demo Mode Software Update Favorite CH Favorite Channel SettingOperation Lock Out IdentificationPress Enter to start updating During the data checking, Checking blinksAfter the screen shown below is displayed, press Remove the USB memory deviceTroubleshooting-Digital Broadcasting TroubleshootingError message about reception of broadcast Problem Possible SolutionSpecifications Optional AccessoryAppendix Model LC-32SB27UInformation on the Software License for This Product PC Compatibility ChartLimited Warranty Calling for Service