Sharp LC 32D47U operation manual Position, PC Setup, PC Audio Select, Hdmi Auto View

Page 21

On-Screen Display Menu

Position

For adjusting a picture's horizontal and vertical position.

H-Pos.:Centers the image by moving it to the left or right.

V-Pos.:Centers the image by moving it up or down.

For resetting adjustments to the factory preset values, press a/b to select "Reset", and then press ENTER.

When connecting a PC to the HDMI terminal, the image position will be automatically adjusted. It cannot be manually adjusted.

Adjustments are stored separately according to input source.

When a DTV channel is selected, the horizontal position cannot be adjusted.

The horizontal and/or vertical position may not be able to be adjusted or it may be adjusted only to a certain degree.

PC Setup

Input Signal (for Analog PC Input Mode Only)

Some input signals may have to be registered manually to display properly. The pair of input signals (resolutions) in the list below is not distinguishable when received.

In such a case, you have to set the correct signal manually. After setting once, it will display when the same signal (resolution) is input again.

1024 x 768

1360 x 768

You can only select the "Input Signal" on the Setup menu when receiving one of the 2 input signals listed above.

Auto Sync. (for Analog PC Input Mode Only)

For automatically adjusting the PC image.

Yes: Auto Sync. starts.

No: This function does not work.

Fine Sync.

Ordinarily you can easily adjust the picture as necessary to change image position using Auto Sync. In some cases, however, manual adjustment is needed to optimize the image.

H-Pos.:Centers the image by moving it to the left or right.

V-Pos.:Centers the image by moving it up or down.

Clock: Adjust when the image fl ickers with vertical stripes.

Phase: Adjust when characters have low contrast or when the image fl ickers.

For resetting all Fine Sync. adjustment items to the factory preset values, press a/b to select "Reset", and then press

ENTER.

It is not necessary to adjust the "Clock" or "Phase" when a digital signal is being input, so it cannot be selected.

The default cursor position may not be in the center, because the screen position variable ranges may be asymmetrical.

PC Audio Select

Determines whether the AUDIO terminal is used for INPUT 4 (PC-IN) or INPUT 5 (HDMI).

Input 4 (PC): Select this item when the audio signal is input via the INPUT 4 (PC-IN) terminal using an analog RGB cable.

Input 5 (HDMI): Select this item when the audio signal is input via the INPUT 5 (HDMI) terminal using an HDMI- DVI conversion cable.

When "PC Audio Select" is set to "Input 5 (HDMI)", sound will not be produced if you use only an HDMI-certifi ed cable to connect HDMI-compatible equipment. To produce sound, you should make an analog audio connection.

If you want to connect HDMI-compatible equipment using only an HDMI-certifi ed cable, set "PC Audio Select" to "Input 4 (PC)".

When Auto Sync. is successful, "Completed" displays. If not, Auto Sync. failed.

Auto Sync. may fail even if "Completed" displays.

Auto Sync. may fail if the computer image has low resolution, has unclear (black) edges, or is moved while executing Auto Sync.

Be sure to connect the PC to the TV and switch it on before starting Auto Sync.

HDMI Auto View

To watch an HDMI or PC-IN equipment image, select "INPUT5", "INPUT6" or "INPUT7" from "INPUT SOURCE" menu using INPUT on the remote control unit or on the TV.

Enable: To use View Mode based on signal recognition, including an HDMI signal.

Disable: No function.

Refer to your external equipment operation manual for the signal type.

When connecting an HDMI-DVI conversion adapter/cable to the HDMI terminal, the image may not come in clearly.

21

Image 21
Contents LC-32D47U Supplied Accessories09P03-MX-NM For connectionsImportant Information Dear Sharp Customer Additional Safety InformationPrecautions when transporting the TV Child Safety Using an optional bracket to mount the TV Setting the TV on the WallAbout setting the TV angle Attaching/Detaching the StandPower indicator on the front of the television lights Green Using the Remote Control UnitConnecting Antenna Cable Installing Batteries in the Remote Control UnitPreparation AntennasTV Front Part NamesTV Rear/Side Input buttonConnecting a PC Connecting to External EquipmentTurning On/Off the Power Initial SetupWatching TV Sleep Timer Changing VolumeDirect Button Operation Changing ChannelsDigital broadcasting audio mode MTS/SAP stereo modeDirect Button Operation ExamplePress Input again or press a/b to select the input source Press InputPress CC Operating On-Screen Display MenuFor PC input mode Press View ModeYou can select the screen size For HD programsUsing the control panel of the main unit Using the remote controlOn-Screen Display Menu On-Screen Display Menu OperationAdvanced Picture Setting OPC SettingPicture Menu Audio Menu Power Control MenuEZ Setup Setup MenuCH Setup Input SkipPosition PC SetupPC Audio Select Hdmi Auto ViewReset Audio SetupParental Ctrl Parental Control Setting LanguageOn-Screen Display Menu Mpaa Voluntary movie rating system When setting an individual content-based rating itemTV Parental Guidelines RatingCanadian English Ratings How to temporarily release the V-CHIP BlockCanadian French Ratings Reactivating the temporarily released V-CHIP BlockOption Menu Demo Mode Favorite CH Favorite Channel SettingIdentification Software Update Operation Lock OutPress Enter to start updating During the data checking, Checking blinksAfter the screen shown below is displayed, press Remove the USB memory deviceTroubleshooting-Digital Broadcasting TroubleshootingError message about reception of broadcast Problem Possible SolutionSpecifications Optional AccessoryAppendix Model LC-32D47USecret number is PC Compatibility ChartLimited Warranty Calling for Service