Sansui SLEDVD249 owner manual TV operation

Signal Type

Cable

E-POP Demo

Off

TV Location

Store

Starting setup

The Auto Setup menu appears the first time you turn on the TV, and assists you to specify the Air/Cable setting, and program your channels automatically.

IMPORTANT: Make sure that the antenna or cable TV system connection is made!

1 To turn on the TV, press POWER (It may take approx. 10 seconds for a picture to appear on screen.). The Auto Setup function begins.

Auto Setup

2		Automatic Search Start
	Press ▲ or ▼ to select “TV Location”, then press
	◀ or ▶ to select “Store” or “Home”. This product
	qualifies for ENERGY STAR in Home mode
	default setting.
	NOTE:
	• This unit has been preset to STORE brightness.
		This setting does not qualify under ENERGY
		STAR. To reduce brightness and energy
		consumption, change setting to ‘HOME’. This
		setting does qualify under ENERGY STAR.
	• The device may not conform to the ENERGY
		STAR standard after “Reset” is performed or the
3		“Backlight” is adjusted.
	Press ▲ or ▼ to select “E-POP Demo”, then press
	◀ or ▶ to select “On” or “Off”.
	On: A TV feature introduction will be popped up
		at the bottom of the screen.
4	Off: Turn off the E-POP Demo feature.
	Press ▲ or ▼ to select “Signal Type”, then press
	◀ or ▶ to select “Cable” or “Air”.
	Press ▲ or ▼ to select “Automatic Search”, then
5 press ▶ or ENTER.

	“Auto Setup” will begin. After the Auto Setup
6 is completed, the TV channel appears on the
	screen.
	• Depending on the reception condition, it may
	take up to 30 minutes to complete memorizing
	digital cable channels. Please allow the
	process to complete without interruption.
NOTE:
•	If you press EXIT in the process of “Auto Setup”,
	the Auto Setup stops and changes to the normal
•	screen.
	When you make a menu selection, your changes
	occur immediately.You do not have to press EXIT to
	see your changes.

TV operation

1	To turn on the TV, press	POWER.
	(It may take approx. 10 seconds for a picture to
2	appear on screen.)
	Adjust the volume level by pressing VOL + or – .
	The volume level will be indicated on the screen
	by green bars. As the volume level increases, so
	do the number of bars. If the volume decreases,
	the number of green bars also decreases.

3 Set the Signal Type option to the appropriate position (see “Air/Cable selection” on page 18).

4 Press the Direct Channel Selection (0-9, –) buttons to select the channel.

(If you press only channel number, channel selection will be delayed for a few seconds.)

TO SELECT ANALOG CHANNELS

1-9: Press 1-9as needed. Example, to select channel 2, press 2, then press

ENTER.

10-99: Press the 2 digits in order. Example, to select channel 12, press 1, 2, then press ENTER.

100-135: Press the 3 digits in order. Example, to select channel 120, press 1, 2, 0, then press ENTER.

TO SELECT DIGITAL CHANNELS

Press the first 1-3 digits, then press the – button, followed by the remaining number.

Example, to select channel 15-1, press 1, 5, –, 1, then press ENTER.

• If a channel is selected with only audio content, “Audio only” will be displayed on the screen.

• If a channel is selected with a weak digital signal, “Digital channel signal strength is low” will be displayed on the screen.

The same program may be available on either an analog channel or a digital channel.You may choose to watch either format.

• If a channel is selected to which you have not subscribed, “Digital channel is encrypted” will be displayed on the screen.

VHF/UHF/CABLE CHANNELS

Air		Cable
VHF		VHF
2-13		2-13
UHF	STD/HRC/IRC
14-69	14-36	(A) (W)
	37-59	(AA) (WW)
	60-85	(AAA) (ZZZ)
	86-94	(86) (94)
	95-99	(A-5) (A-1)
	100-135 (100) (135)
	01	(4A)

NOTE:

• If a channel with no broadcast is selected, the sound will automatically be muted.

• It may take a few seconds for a digital channel picture to appear on screen after being selected.

15EN