Sylvania 6620LDT owner manual TV Operation and Settings, Initial SET UP, Watching a TV Program

Page 11
- HELPFUL HINTS -
1. PLEASE CHECK TO SEE IF THE ANTENNA/CABLE/SATELLITE IS PROPERLY CONNECTED.
2. DID YOU PERFORM “AUTO PRESET CH” ?
3. PLEASE REFER TO FRONT PAGE OF THE OWNER’S MANUAL OR REAR PANEL FOR SUPPORT LINE INFORMATION.

TV SECTION

TV OPERATION AND SETTINGS

INITIAL SET UP

When you turn on the power for the first time,

TV

the SELECT LANGUAGE screen is displayed.

Select the language for screen display and perform auto programming of the channels.

1 After antenna or cable connection is completed, connect the power cord into a standard AC outlet.

NOTE

If any digits are displayed in the corner of the screen, press [POWER] without unplugging the power cord.

2 Press [POWER] to turn on the unit.

POWER

WATCHING A TV PROGRAM

1 Press[POWER] to turn on the unit.

POWER

NOTE

If the TV screen shows snow noise and there is no operation for more than 5 seconds, “HELPFUL HINTS” appears.

Follow the instructions listed on-screen.

If those settings do not work properly, please call our help line on the front page of this owner's manual.

2 Press [CH. K / L] or the Number buttons to select the desired channel number.

 

 

1

2

3

 

OR

4

5

6

CH.

7

8

9

TV OPERATION AND SETTINGS

SECTION

3 Press one of the keys listed below to select the desired language of on-screen menu.

ENGLISH: [CH. K]

ESPAÑOL: [CH. L]

FRANÇAIS: [VOL. X]

4 Confirm the antenna (or cable) connection and press [CH. K].

The tuner scans and memorizes all active channels in your area.

5 When the scanning is completed, the tuner stops on the lowest memorized channel.

SELECT LANGUAGE

ENGLISH

NEXT:PRESS CHK

ESPAÑOL

DESPUÉS:PRESIONE CHL

FRANÇAIS

APRÈS:PRESSEZ VOLX

 

 

 

 

– INITIAL SETUP –

PLEASE CONNECT ANTENNA OR CABLE OR SATELLITE TO THIS UNIT.

THEN PRESS CH K,

IN ORDER TO PERFORM “AUTO PRESET CH ”.

CH 15

 

+100

0

+10

NOTE

For channel number selection with number buttons:

To select single-digit channel number, press

[0]first. (e.g. Press [0] [2] for channel 2.)

To select cable channels which are higher than 99, press [+100/+10] first.

(e.g. Press [+100/+10] [2] [5] for channel 125.)

3 Press [VOL. X / Y] to select the desired vol- ume level.

VOL.

 

VOLUME 20

C C C C C C C C C C C C C C C C

TV

(Example)

NOTE

If [MENU] is pressed during channel scanning, the tuner stops scanning and the lowest memo- rized channel is displayed.

The INITIAL SETUP menu is displayed every time you turn on the unit unless the scanning is completed.

In case no channel can be received by the channel scan-

ning, “NO TV SIGNALS” is

NO TV SIGNALS

displayed on the screen. Turn

 

off the unit and check the

 

antenna connection, then

 

follow steps 1 to 5 again.

 

You can change the setting after completing INITIAL SET UP by LANGUAGE menu or CHANNEL SET UP menu. (Refer to “MENU LANGUAGE” on page 16 or “CHANNEL SET UP” on page 12).

Press [MUTE] to instantly mute the sound.

Press it again to restore the previous volume level.

NOTE

If you press [CH. K / L] in the DVD mode, you can change the TV channels. Even if you turn off the unit in the DVD mode, when you turn it on again, it will go into the TV mode.

TO WATCH CABLE OR SATELLITE CHANNEL

If the unit is connected to a cable box or satellite box, press [CH. K / L] to select CH3 or CH4 according to the output channel setting of the device and select desired channel on that device.

TO WATCH EXTERNAL INPUT

When an external equipment is connected to AUDIO/VIDEO input jacks on the right side, press [SELECT] or [CH. K / L] repeatedly until “VIDEO1” or “VIDEO2” appears on the screen.

- 11 -

EN

Image 11
Contents 6620LDT 20 inch Risk of Electric Shock Do not Open PrecautionsImportant Copyright Information Moisture Warning Supplied AccessoriesSymbols Used in this Manual LocationTable of Contents TV Mode FeaturesOperating Controls and Functions Remote Control+100 button For TV mode +10 button For DVD modeControl Panel Installing the BatteriesBattery Precautions ANTENNA/CABLE Connection If YOU have a Wired CableWhen Using Cable BOX/SATELLITE BOX Preparation for USEExternal Connection To Watch Cable or Satellite Channel TV Operation and SettingsInitial SET UP Watching a TV ProgramAdded channel Light blue Deleted channel Light red Channel SET UPAuto Channel Programming ADDING/DELETING ChannelsPicture Control Back Light SettingSleep Timer To Check the Sound Status To Select TV Sound ModePress Audio repeatedly to select the MTS output mode Closed Caption SystemPress Setup then press K or L to point to V-CHIP SET UP Chip SET UPChip SET UP TV Rating SET UPMenu Language Mpaa Rating SET UPChange Access Code Press Setup then press K or L to point to LanguageAbout the Discs About the DiscsPlayable Discs Unplayable DiscsMP3 Playback Playing a DiscBasic Playback Getting StartedPause Disc MenuTitle Menu ResumePress FWD g or REV h Slow Forward Slow ReverseDuring playback, press FWD g or REV h To return to normal playback, press Play OTitle / Chapter Search Press Search ModeSearch Function Track SearchRepeatedly Marker SET UP ScreenPress Search Mode or Return to exit Time SearchClear Special Playback FunctionRepeat FunctionEnter ProgramRandom Playback Audio Language Changing the SettingsStereo Sound Mode Subtitle LanguageFor CD play only Black Level SettingCamera Angle ReturnInformation Changing the Settings / the ON-SCREENON-SCREEN Information Custom Menu Changing the DVD SET UP ItemsLanguage Setting Display SettingParental Control Audio SettingsWhen playing disc with copyright protection Changing the DVD SET UP ItemsInitialize Other SettingsCable Channel Designations Language Code ListAdjust Contrast & Brightness control Troubleshooting GuideCAPTION2 or Caption OFF Closed Caption Problem Possible RemedyUsing digital camera Using AM radioDVD MaintenanceSpecifications Disc HandlingMando a Distancia IndiceControles DE Operación Y Funciones NotaPanel DE Control Para Insertar LAS PilasPrecauciones a LA Hora DE Insertar LAS Pilas SI Tiene Cable DE Hilos Preparación Para LA UtilizaciónConexiones DE ANTENA/CABLE SI Tiene UNA Toma DE ParedSalida DE Audio Conexión ExternaEntrada DE VÍDEO1 Entrada DE VÍDEO2Para VER UN Canal POR Cable O Satélite Presione Power para encender la unidadOperación DE TV Y Ajustes Instalación InicialLish o Langage FRANÇAIS, y a Ajuste DE CanalIdioma DE Menú Presione EnterReproducción DE MP3 Reproducción DE UN DiscoReproducción Básica Para EmpezarDurante la reproducción, presione Stop C Menú DE DiscoReanudación Presione Disc MenuTel Limited Warranty