Setup
Connections
Please refer to “Basic TV Connection” on the front page before you use this unit.
RF Output Channel
If channel 3 is already occupied for broadcasting,
1)Set your TV to channel 4.
2)Insert a
3)Press [OUTPUT] on the unit so that the VCR OUTPUT light is lit.
•If noise appears on the TV screen, press [VCR/TV] on the remote control.
4) Press [PLAY B] once.
5)After a few seconds, hold [PLAY B] on the unit for 3 seconds.
•The RF output channel will change to channel 4 from channel 3 and you will see a playback pic- ture.
•When a picture does not appear on the TV screen, repeat step 4).
6) Press [STOP C] to stop playback.
Hint
•The RF output channel may not change when you adjust tracking during playback. In this case, stop the playback, and start the playback again. After that, hold [PLAY B] on the unit for 3 seconds again.
Setup
Hint for Cable Box or Satellite Box
Satellite or | (Cable box or |
| (Back of DVD/VCR) | ||
Satellite box) |
| ||||
Cable TV |
| ||||
IN |
|
|
| ||
signal | OUT | RF cable | |||
| |||||
|
|
|
| ||
(supplied)
(Back of TV)
Select this connection when you want to view or record a scrambled channel. With this connection, channels cannot be changed on the unit. You can view or record ONLY the chan- nels you have selected on the cable box or the satellite box.
• While you are recording, only the recorded channel can be viewed.
To select channels of the cable box or satellite box
1)Turn on the unit by pressing [POWER], then press [VCR/TV]. The “POWER” light on the front panel will appear, then press [SKIP/CH. G/K H/L] to select chan- nel 3 or 4 (the same channel as the output channel of the cable box or satellite box).
•If you use the channel 4, you need to change the unit’s RF output to channel 4. Refer to “RF Output Channel”.
2)At the TV, select channel 3 or 4 (the same channel as you have selected at step 1).
3)On the cable box or satellite box, select the channel you want to view or record.
Connection to an Audio System
Method 1
Stereo system
L | R | Analog audio |
AUDIO |
| input jacks |
Audio cable
(supplied)
| DVD/VCR | VCR |
(Analog) | AUDIO OUT |
|
L |
| |
AUDIO OUT | R |
|
DVD/VCR
or
DVD
DIGITAL | AUDIO | COMPONENT | |
VIDEO OUT | |||
AUDIO OUT | OUT | OUT |
|
L
R
(DVD mode only)
Setting | SETUP > QUICK > |
Connection | DOLBY DIGITAL |
Connecting to Stereo System. | PCM |
* To complete these settings, refer to pages
Hint
•Playing a DVD using incorrect settings may generate noise distortion and may also damage the speakers.
Method 2
Dolby Digital decoder,
MD deck or DAT deck
| COAXIAL | Digital audio | |
|
| input jack | |
Audio Coaxial |
|
|
|
Digital cable |
|
|
|
(commercially |
|
|
|
available) |
|
|
|
|
| DVD |
|
| DIGITAL | AUDIO | COMPONENT |
| VIDEO OUT | ||
AUDIO OUT | OUT OUT |
| |
DIGITAL | COAXIAL |
|
|
AUDIO OUT |
|
| |
|
|
| |
Connection | Setting | SETUP > QUICK > | |
|
| DOLBY DIGITAL | |
Connecting to a Dolby Digital decoder | BITSTREAM | ||
for Dolby Digital audio output. |
| ||
|
| ||
Connecting to the other equipment (an MD deck | PCM | |
or DAT deck etc.) without Dolby Digital decoder. | ||
|
* To complete these settings, refer to pages
Hint
•The audio source on a disc in a Dolby Digital 5.1 channel surround format cannot be recorded as digital sound by an MD or DAT deck.
•By hooking this unit up to a
•Playing a DVD using incorrect settings may generate noise distortion and may also damage the speakers.
– 6 – | EN |