JVC HD-61Z886, HD-70G886, HD-61Z786 manual Remove the lamp unit, Install the new lamp unit

Page 97

Appendix

WARNING: DO NOT attempt to remove the assembly until the lamp has fully cooled. If you feel any heat near the lamp, STOP and wait until the lamp has FULLY COOLED.

NEVER attempt to remove the lamp with the television plugged into an outlet.

DO NOT DROP the used lamp. The inside of the lamp is under pressure. Dropping or other hard shock could cause the lamp to shatter.

ALWAYS recycle the used lamp. Because the lamp contains a small amount of mercury, it cannot be thrown away with regular trash. Follow the recycling instructions included with the Lamp Replacement Kit.

6) Remove the lamp unit.

Using a Philips head type screwdriver (cross-head type), loosen the two screws fastening the lamp unit. When the screws have been loosened, remove the lamp by raising the handle and gently sliding the unit straight towards you. Place it carefully in the recycling packaging.

7) Install the new lamp unit.

Holding the handle attached to the new lamp unit, slide and push the new lamp straight into the television and back into the lamp housing area. Do not forget to re-tighten the two screws.

Note: If the lamp does not sit securely in the TV (flat in the lamp housing area), it won’t turn on. Make sure the lamp sits securely and flat in the housing area.

WARNING!

Remember it is very important that YOU DO NOT TOUCH THE LAMP SURFACE. Please read the warnings on page 94 again.

Also, replace the lamp with part number TS-CL110U only! The television is designed to work specifically with this lamp. Lamps other than TS-CL110U may cause malfunctions and/or other damage to the television.

NOTICE (for USA)

This product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information, please contact your local authorities, or the Electronics Industries Alliance: http://www.eiae.org

To purchase a replacement lamp kit, please call 1-800-252-5722.

97

Image 97

Contents Projection Television Users Guide Risk of Electric Shock Do not Open Important Safety PrecautionsImportant Safety Instructions FCC Notice Caring for the Screen Caring for the CabinetOrder to use the television for a long time When the power is turned on, the warming up commencesCooling the inside of the television and the lamp Lamp is a consumable itemILA element characteristics Television requires a lot of electrical powerScreen is made of plastic Do not replace the lamp immediately after useTable of Contents Digital Button Functions Digital SetupMedia Card Viewer OSD InformationQuick Setup Unpacking your TV Video Cable Coaxial CablesComponent Cables Composite Cables Audio Cables AV CompuLink CableHD-70G886 HD-61Z886 HD-61Z786 Rear Panel DiagramSide Panel Diagram Front Panel DiagramModels HD-70G886, HD-61Z886, HD-61Z786 Quick Setup TV Remote Control Remote Control Key Feature ButtonsBasic Operation Getting StartedVideo Cable Component Cables Composite Cables Audio Cables Connecting Your DevicesVCR Connection Diagram #2 Connecting to Monitor/Recording Output Terminal AV CompuLink Cable Connecting to JVC AV Compu LinkConnecting to a Camcorder Connecting to an External Amplifier Connecting to the Surround AmplifierConnecting to an amplifier using your optical output Connecting to a Digital TV Receiver Connecting to an Hdmi Compatible Device Monitor OUT Link Compatible Device Looking at the images from a computer Connecting to the computerWhen a picture is not displayed Table of signals for each type of computerTo be LanguageInteractive Plug In Menu Manual Clock Set Auto Clock SetNOW Programming Auto Tuner SetupRemote Programming Setting the CATV, VCR and DVD CodesCable Box or Satellite Codes MGA VCR CodesSMC DVD CodesCable/Satellite Search Codes Function Search CodesVCR/DVD Search Codes Function Onscreen Menus Using the GuideOnscreen Menu System Onscreen Menu SystemSelected Option Green Selected Option BlueTo Initial Setup Auto Tuner Setup Initial SetupDigital Channels Channel SummaryContinue to follow these directions for all four spaces Chip Channel Guard MessageDirections to Block Unrated Programs Unrated ProgramsUS V-Chip Ratings Directions to set US V-Chip Ratings Setting US V-Chip RatingsDirections to set Movie Mpaa Ratings Movies RatingsDirections to set Canadian V-Chip Ratings Canadian V-Chip RatingsSet Lock Code Language Auto DemoDigital Auto Setting Analog SettingClosed Caption Digital Manual Setting Noise Muting Auto Shut OffV1 Smart Input Front Panel LockVideo Input Label Power Indicator Position AdjustmentTV Speaker Video-1 Monitor OutAudio Out Digital-In Audio Digital-InCenter CH Input Picture Settings Picture AdjustAdjust the Picture Settings Color TemperatureColor Management Digital Noise ClearDynamic Gamma Smart Picture ResetSound Settings Sound AdjustAdjust the Sound Settings Set Clock Clock/TimersOn/Off Timer Following message will appear Lamp Timer ResetMulti Screen Function Button FunctionsTwin Freeze IndexSwap SelectNumber Buttons 10Key Pad PowerTune InputSound Return +/TVVideo Status MutingNatural Cinema Sleep Timer Message Sleep TimerDisplay Volume +Channel + Register the favorite channel FavoriteDelete the favorite channel Aspect Aspect Ratios in PC ModeAspect Ratios Back MenuVCR/DVD Slide Switch TV/CATV Slide SwitchVCR Buttons DVD ButtonsAntenna Level Digital SetupAspect Ratio Digital SoundCable Card Application Software UpdateLink Auto Play Digital CH D/A Digital/Analog Digital Button FunctionsSub Channel To watch digital channelsController Link MenuTo operate, select a device DeviceReservation TimerTimer Edition Timer EditTimer Deletion Guide Cancel the timer recordingMedia Card Note Media Card ViewerCard slot, this menu will not appear Rotation PhotoFile and Extensions FileInvalid Signal Weak SignalOSD Information No ProgramCable Card Connection Cable Card InformationProblems Check TroubleshootingFollowing are not malfunctions Changing the Lamp AppendixLamp Message Replacement Lamp KitUnplug the television How to Replace the LampRemove a screw from the rear panel Remove the left speaker panelRemove the lamp unit Install the new lamp unitRe-install the left speaker panel Re-install the lamp coverRe-install the screw to the rear panel Power LED and LAMP/PROGRAM LED blink alternately Power LED blinksPower LED and LAMP/PROGRAM LED blink rapidly simultaneously LAMP/PROGRAM LED blinks100 101 Specifications subject to change without notice Specifications103 JVC Company of America JVC CANADA, INC