JVC PD-42X50BU, PD-42X50BJ, PD-42X50BS manual „ Poor sound, „ Other issues

Page 57

Troubleshooting

When viewing images from commercially available video software products, or videos from videotapes which have been recorded improperly, the top of the image may be distorted. This is due to the condition of the video signal. There is nothing wrong with the TV.

Since this TV is designed to make full use of the resolution of the original video source, the motion may appear unnatural when the video source is input with 625p progressive-scanning component signals. If this occurs, change the output setting of the connected device to 625i interlace- scanning component signal output. See the instructions that came with the device for more information.

„Poor sound

Have you adjusted BASS or TREBLE properly? If not, follow the description “BASS” or “TREBLE” on page 33.

When TV channel reception is poor, it can be hard to hear stereo or bilingual sound. In this case, follow the description “STEREO / I • II” on page 33 to hear the sound more easily by changing it to a mono sound.

„If the TV does not respond to the remote control

Have the batteries of the remote control worn out? Follow the description “Putting the batteries into the remote control” on page 8 and replace them with new batteries.

Have you attempted to use the remote control from the sides or rear of the TV or from more than seven metres away from the TV? Use the remote control in front of your TV or from less than seven metres away.

When you are viewing a teletext programme, you cannot operate the menus. Press the b button to return to the ordinary TV programme, and then try operating the menus.

If the TV suddenly stops responding, press the Abutton on the TV and turn off the TV. Press the Abutton again to turn on the TV. If the TV returns to a normal state, it is not a failure.

„Other issues

When the SLEEP TIMER function operates, the TV is automatically turned off. If the TV suddenly turns off, try to press the #(standby) button to turn on the TV once again. If the TV goes back to normal, there is no problem.

When the TV is receiving a wide-screen signal (WSS) or a signal from an external device affecting the screen size, the ZOOM mode automatically changes. When you want to resume the previous ZOOM mode, press the cbutton again.

If you bring magnetised equipment such as a speaker near to your TV, the picture may be warped or unnatural colours may appear at the corners of the screen. In this case, keep the equipment away from your TV. If speakers cause this to happen, use magnetically-shielded speakers instead.

It takes a short period of time from the time an operation such as changing channels is performed until an image is displayed. This is not a fault. This is the time needed for the image to stabilize before it can be displayed.

The TV may make a crackling sound due to a sudden change in temperature. The picture or sound may be normal. If you hear crackling sounds frequently while you are viewing the TV, there may be other causes. As a precaution, ask your service technician to inspect it.

Touching the screen may cause you to feel a slight electric shock due to its static electricity. This is unavoidable due to the construction of the picture tube. It is not a problem with the TV. You can rest assured that this static discharge is not harmful.

ENGLISH

55

Image 57
Contents PD-42X50BU PD-42X50BJ PD-42X50BS „ Warning How to replace the fuse„ If in doubt consult a competent electrician „ Guidelines for safe operationDistance recommendations Burn-in „ Do not view for long periods of time in the Regular modeAvoid burn-in as follows If Burn-in has occurredPixel defects Effect on infrared devicesPicture Management demonstration Contents Checking the contents of packages Setting up your TV Installation„ Only use JVC approved accessories with your model Decoder EXT-2 on Connecting the aerial and video cassette recorder VCRPutting the batteries into the remote control Connecting the power cord to the AC outlet„ Rear Panel Attaching the ferrite coresInitial settings Press the a buttonPress the Abutton on the TV Press the blue button to start the Auto Program function Press the a button to display the T-V Link menuIf you do not have a T-V Link compatible VCR connected „ ACI function If ACI Error is displayed in the Auto Program menu„ Downloading the data to VCR If ACI START/ACI Skip appears in the Auto Program menuLink functions When Feature not Available is displayed„ Pre-set download Turn on the VCR Press the a button„ Direct Rec Adjust the volume Turn the TV on from standby modeUsing the Menu TV buttons and functionsRemote control buttons and functions Turn the TV on or off from Standby modePress the # standby button to turn TV on or off Choose a TV channel and watch images from external devices To return to a TV channelTo use the programme number PR 0 AV Information function Press the r q buttons to adjust the volumeChannel number display Time displayZoom function „ Choose the Zoom mode„ Adjusting the visible area of the picture Using the Freeze function3D Sound function Return to TV channel instantlyUsing the MULTI-PICTURE function Press the XbuttonPictures multi To return the multi-picture to one screen Favourite channel function „ Setting the picture effect„ Favourite channel registration „ Calling the favourite channelOperating a JVC brand VCR or DVD player Set the VCR/TV/DVD Switch to the VCR or DVD position„ Showing the favourite channels VCRPress B button to go into the List mode Using the List ModeTeletext function Basic operationSub-page HoldReveal SizePress H Cancel button CancelIndex Press the G Index buttonPress the Hbutton to display the menu bar Using the TV’s menuUsing the TV’s menu Picture menu Features „ Digital VNR„ Super DigiPure „ Colour Management „ Movie Theatre„ Picture Management „ 43 Auto Aspect „ Colour SystemSound menu BBE SpeakerCentre Sleep Timer Features menuChild Lock „ To set the Child Lock functionAppearance Blue Back„ To view a locked TV channel Choose Favourite SETTING, then press the a or 3 button Favourite SettingRefresh Choose Refresh Press the a buttonSET UP menu Auto ProgramEDIT/MANUAL „ Move „ Basic operationChoose EDIT/MANUAL, then press the a or 3 button Press the 3 button to start the Move function„ ID „ DeletePress the yellow button to delete the TV channel Press the red button to start the ID function„ Manual „ InsertUnited Kingdom FranceDecoder EXT-2 Language„ S-IN S-VIDEO input EXT SettingID List Dubbing„ ID List To cancel the S-IN S-VIDEO input settingPress the 5 or 6 buttons to choose an EXT terminal To erase a name assigned to the EXT terminalPicture Shift Hdmi Setting„ Dubbing SlowTable of signals for each type of computer Connecting to the computerWhen a picture is not displayed Displaying a computer screen„ Connecting the PC Connecting external equipmentBefore connecting anything Additional preparation„ Connecting speakers/amplifier „ Connecting headphones„ Video or sound signal output from the EXT-2 terminal „ T-V Link compatible VCR„ Using the TV speaker as the surround centre speaker Using the Hdmi terminal „ Connecting a Hdmi compatible device„ Setting Hdmi Setting When setting Size When setting AudioPress the 6 buttons and choose Size or Audio Channel CH/CC numbersCH/CC numbers „ If you cannot turn on the TV Troubleshooting„ If you cannot turn off the TV „ No picture or no sound„ If the TV does not respond to the remote control „ Other issues„ Poor sound We may change the design and specifications without notice Specifications