JVC LCT1781-001A „ Poor sound, „ If the TV does not respond to the remote control, „ Other issues

Page 56

Troubleshooting

ENGLISH

•When viewing images from commercially available video software products, or videos from videotapes which have been recorded improperly, the top of the image may be distorted. This is due to the condition of the video signal. There is nothing wrong with the TV.

•Since this TV is designed to make full use of the resolution of the original video source, the motion may appear unnatural when the video source is input with 576p progressive-scanning component signals. If this occurs, change the output setting of the connected device to 576i interlace- scanning component signal output. See the instructions that came with the device for more information.

„Poor sound

•Have you adjusted BASS or TREBLE properly? If not, follow the description “BASS” or “TREBLE” on page 34.

•When TV channel reception is poor, it can be hard to hear stereo or bilingual sound. In this case, follow the description “STEREO / I • II” on page 34 to hear the sound more easily by changing it to a mono sound.

•If you cannot hear the normal sound even if the picture of the TV channel appears normally. Follow the description “EDIT/ MANUAL” on page 39 to use the MANUAL function to change the SYSTEM setting.

„If the TV does not respond to the remote control

•Have the batteries of the remote control worn out? Follow the description “Putting the batteries into the remote control” on page 7 and replace them with new batteries.

•Have you attempted to use the remote control from the sides or rear of the TV or from more than seven metres away from the TV? Use the remote control in front of your TV or from less than seven metres away.

•When you are viewing a teletext programme, you cannot operate the menus. Press the 4button to return to the ordinary TV programme, and then try operating the menus.

•If the TV suddenly stops responding, press the Abutton on the receiver and turn off the TV. Press the Abutton again to turn on the TV. If the TV returns to a normal state, it is not a failure.

„Other issues

•If the CHILD LOCK function set to ON, you cannot operate the TV with the front control buttons of the TV. Set the CHILD LOCK function to OFF.

•When the SLEEP TIMER function or AUTO SHUTOFF function operates, the TV is automatically turned off. If the TV suddenly turns off, try to press the # (standby) button to turn on the TV once again. If the TV goes back to normal, there is no problem.

•When the TV is receiving a wide-screen signal (WSS) or a signal from an external device affecting the screen size, the ZOOM mode automatically changes. When you want to resume the previous ZOOM mode, press the cbutton again.

•If you bring magnetised equipment such as a speaker near to your TV, the picture may be warped or unnatural colours may appear at the corners of the screen. In this case, keep the equipment away from your TV. If speakers cause this to happen, use magnetically-shielded speakers instead.

•It takes a short period of time from the time an operation such as changing channels is performed until an image is displayed. This is not a fault. This is the time needed for the image to stabilize before it can be displayed.

•The TV may make a crackling sound due to a sudden change in temperature. The picture or sound may be normal. If you hear crackling sounds frequently while you are viewing the TV, there may be other causes. As a precaution, ask your service technician to inspect it.

•Touching the screen may cause you to feel a slight electric shock due to its static electricity. This is unavoidable due to the construction of the picture tube. It is not a problem with the TV. You can rest assured that this static discharge is not harmful.

54

Page 55 Page 57
Image 56
Page 55 Page 57
Contents PD-Z50DX4 Page Table top stand is an option Distance recommendations „ Do not view for long periods of time in the Regular mode Burn-inAvoid burn-in as follows If Burn-in has occurredPicture Management demonstration Pixel defectsEffect on infrared devices Contents Checking the contents of packages Setting up your TV InstallationPutting the batteries into the remote control „ Only use JVC approved accessories with your modelConnection diagram ConnectionsTV back Receiver back„ If not connecting a VCR see Fig. a Disconnecting the system cable„ If connecting a VCR see Fig. B „ Receiver rearBack of the receiver Connecting the power cord to the AC outletBack of the TV Initial settings Setup tour Press the Abutton on the receiverTV front Press the a buttonNow, setting up is complete. Please enjoy your new JVC TV Turn the TV on from standby mode TV front TV back Receiver front How to open the coverTV buttons and functions To turn the TV offAdjust the volume Using the MenuPress the Volume q buttons Choose a TV channelPress the # standby button to turn the TV on or off Remote control buttons and functionsTurn the TV on or off from standby mode To use the programme number PR 0 AV Choose a TV channel and watch images from external devicesTo return to a TV channel Press the 7q buttons to adjust the volume Display functionPR List Channel number display„ Choose the Zoom mode Zoom functionCinema Surround function Using the Freeze function„ Adjusting the visible area of the picture Using the MULTI-PICTURE function To cancel the Freeze functionPress the Xbutton Pictures multi„ Return function Return Plus function and Return function„ Return Plus „ Setting the picture effect Favourite channel function„ Favourite channel registration „ Calling the favourite channelPress the DVD Control Button to control your DVD player Set the PIP/TV/DVD Switch to the DVD positionOperating a JVC brand DVD player Using the List Mode Teletext functionBasic operation „ To store the page numbersSub-page RevealHold SizeCancel Press H Cancel buttonIndex Press the G Index buttonUsing the TV’s menu Press the Hbutton to display the menu barOperation with the buttons on the receiver Picture menu „ Super DigiPure Features„ Digital VNR „ Colour Management „ Pull Down„ Picture Management „ Colour System„ 43 Auto Aspect MainSUB PALSound menu Center BBESpeaker Features menu Sleep TimerChannel Guard „ To set the Channel Guard functionAppearance „ To view a locked TV channelFavourite Setting Blue BackChild Lock Auto ShutoffSET UP menu Auto ProgramEDIT/MANUAL Move„ Basic operation „ MoveDelete Manual„ Insert „ Delete„ ID „ Manual Press the green or red button to search for a TV channelAI Volume VIDEO-1 SETTING/VIDEO-3 SettingLanguage VideoHdmi Setting Teletext Language Picture ShiftSlow FastConnecting to the computer Table of signals for each type of computerWhen a picture is not displayed Displaying a computer screenConnecting external equipment „ Connecting the PCBefore connecting anything Additional preparation„ Connecting headphones „ Connecting speakers/amplifier„ Using the TV speaker as the surround centre speaker „ TV output from the OUT terminal„ Connecting AV Compu Link supported devices Conditions to use the AV Compu Link remote control systemIf a VCR is connected to the VIDEO-1 terminal If a DVD player is connected to the VIDEO-1 terminalIf a VCR is connected to the VIDEO-2 terminal If a DVD player is connected to the VIDEO-2 terminal„ Setting Hdmi Setting Using the Hdmi terminal„ Connecting a Hdmi compatible device Press the 6 buttons and choose Size or Audio When setting SizeWhen setting Audio CH/CC numbers OirtTroubleshooting „ If you cannot turn on the TV„ If you cannot turn off the TV „ No picture or no sound„ Poor sound „ If the TV does not respond to the remote control„ Other issues Specifications We may change the design and specifications without noticeEnglish Page Victor Company of Japan, Limited 1104MKH-CR-VP
Top Page Image Contents