TROUBLESHOOTING
5Troubleshooting Guide
If the unit does not perform properly when operated as instructed in this owner’s manual, check the following chart once before calling for service.
Symptom
Remedy
No power | • Be sure the power cord is plugged in. |
| • If a power failure occurs, unplug the power cord for 30 minutes to allow the unit to |
| reset itself. |
No picture or sound | • Check if the power is on. |
| • Check the outlet connection. |
| • Check the antenna or cable connection to the main unit. |
| • When the outside antenna is used, check the wire condition and connection. |
| • View other TV channels. The problem might be limited to the broadcasting station. |
| • Turn off the power and wait for about 1 minute, then turn it on again. |
No color | • Check the antenna or cable connection to the main unit. |
| • When the outside antenna is used, check the wire condition and connection. |
| • View other TV channels. The problem might be limited to the broadcasting station. |
| • Adjust “COLOR” in “PICTURE” menu. |
Sound OK, picture poor | • Check the antenna or cable connection to the main unit. |
| • When the outside antenna is used, check the wire condition and connection. |
| • Electrical interference from nearby appliances may affect picture quality. |
| • Adjust “CONTRAST” and “BRIGHT” in “PICTURE” menu. |
| • View other TV channels. The problem might be limited to the broadcasting station. |
Picture distorted | • When the outside antenna is used, check the wire condition and connection. |
| • View other TV channels. The problem might be limited to the broadcasting station. |
Weak picture | • Check the antenna or cable connection to the main unit. |
| • When the outside antenna is used, check the wire condition and connection. |
| • Adjust “CONTRAST” and “BRIGHT” in “PICTURE” menu. |
| • View other TV channels. The problem might be limited to the broadcasting station. |
Lines or streaks in picture | • When the outside antenna is used, check the wire condition and connection. |
| • Electrical interference from nearby appliances may affect picture quality. |
| • View other TV channels. The problem might be limited to the broadcasting station. |
Picture blurred | • When the outside antenna is used, check the wire condition and connection. |
| • View other TV channels. The problem might be limited to the broadcasting station. |
Ghosts in picture | • Check the antenna or cable connection to the main unit. |
| • When the outside antenna is used, check the wire condition and connection. |
| • Electrical interference from nearby appliances may affect picture quality. |
| • View other TV channels. The problem might be limited to the broadcasting station. |
Bars on the TV screen | • When the outside antenna is used, check the wire condition and connection. |
| • Electrical interference from nearby appliances may affect picture quality. |
Picture rolls vertically | • When the outside antenna is used, check the wire condition and connection. |
| • Electrical interference from nearby appliances may affect picture quality. |
| • View other TV channels. The problem might be limited to the broadcasting station. |
Different color marks on the | • Move the unit away from nearby electric appliances. Turn off the power and wait |
TV screen | 30 minutes before turning it back on. |
| • View other TV channels. The problem might be limited to the broadcasting station. |
Poor reception on some | • Check the antenna or cable connection to the main unit. |
channels | • When the outside antenna is used, check the wire condition and connection. |
| • Electrical interference from nearby appliances may affect picture quality. |
| • View other TV channels. The problem might be limited to the broadcasting station. |
Picture OK, sound poor | • Electrical interference from nearby appliances may affect picture quality. |
| • View other TV channels. The problem might be limited to the broadcasting station. |
No reception of digital signals | • Make sure auto channel scan has been completed (Refer to “Auto Channel Scan” on |
| page 11). |
| Auto channel scan must be completed when you set up the unit for the first time |
| or move it to a location where previously unavailable channels are broadcast. |
| • The selected channel may not be broadcasting. |
| • When auto channel scan is interrupted and not completed, some channels will not |
| be received. Make sure to complete (Refer to “Auto Channel Scan” on page 11). |
22
EN