Daewoo DSC-3220E/3220L service manual CRT Measurement and Control

Page 51

Service manual SC-150

5-3-15 CRT Measurement and Control

The display processor is equipped with an 8-bit ADC for all measuring purposes. The ADC is connected to the SENSE input pin. Cutoff and white-drive current measurement are carried out during the vertical blanking interval.

5-3-16 Average Beam Current Limiter

The average beam current limiter (BCL) uses the SENSE input for the beam current measurement. The BCL uses a different filter to average the beam current during the active picture. The filter bandwidth is approx. 2 kHz. The beam current limiter has an automatic offset adjustment that is active two lines before the first cutoff measurement line. The beam current limiter function is located in the front-end. The data exchange between the front-end and the back-end is done via a single-wire serial interface. The beam current limiter allows the setting of a thresh-old current. If the beam current is above the threshold, the excess current is low-pass filtered and used to attenuate the RGB outputs by adjusting the white-drive multipliers for the internal (digital) RGB signals, and the analogue contrast multipliers for the analogue RGB inputs, respectively. The lower limit of the attenuator is programmable, thus a minimum contrast can always be set. During the tube measurement, the ABL attenuation is switched off. After the white-drive measurement line it takes 3 lines to switch back to BCL limited drives and brightness.

5-3-17 Analogue RGB Insertion

The VCT 38xxA allows insertion of external analogue RGB signals. The RGB signal is key-clamped and inserted into the main RGB by the Fast-Blank switch. The external RGB input can be overlaid or underlaid to the digital picture. The external RGB signals can be adjusted independently as regards DC level (brightness) and magnitude (contrast). All signals for analogue RGB insertion (RIN, GIN, BIN, FBLIN) must be synchronised to the horizontal flyback, other- wise a horizontal jitter will be visible. The VCT 38xxA has no means for timing correction of the analogue RGB input signals. RGB signals are not digitalised and therefore cannot be processed by the picture scaler.

5-3-18 Fast-Blank Monitor

The presence of external analog RGB sources can be detected by means of a Fast-Blank monitor. With a special monitor logic it is possible to detect if there is an external RGB source active and if it is a full screen insertion or only a box. The monitor logic is connected directly to the FBLIN pin. The controlling software uses this information to disable all picture format using display scaler.

5-3-19 Vertical and East/West Deflection

The calculations of the vertical and East/West deflection waveforms is done by the internal Fast Processor (FP).

The algorithm uses a chain of accumulators to generate the required polynomial waveforms. To produce the deflection waveforms, the accumulators are initialised at the beginning of each field. The initialisation values must be computed by the TV control processor and ar e written to the front-end once.

-50-

Image 51
Contents Chassis SC-150 Contents General description Main PCB Union PCB Tuning system Main FeaturesPower consumption Sound Output PowerSvhs Pin Signal Description Matching value Page C04 C01C02 C03639.25 S13 S10S11 S12Special case Country selection = Others Program Group SkipITV RAY Radiation Precaution Safety instructionHOR Width Order Default settingh for SC-150Alignment instructions ParabolaOption HOR Paral BOW HOR Width Corner EW Trapez VCT IC descriptionPage Page IC version VCT 3832A VCT 3834A Chassis IC marking OSD languages Atss countries TextPin Name Type Short Description Gndaf Supply AGC Page German 2-Carrier System Dual FM System DSP-Section Audio Baseband ProcessingAnalogue Section Nicam plus FM/AM-MonoAdrsel PALSECAM-L UssrVREF2 ResetqDvsup DvssXtalin FeaturesANAIN1 TestenPin Symbol Function Mode OUT1GND1 OUT1+TDA8946J Page GND Block diagram TDA6107Q SCL SDAPage TJ TSD Pin Name Symbol DescriptionVIN OVP IIN HDescription IC Pins Symbol Rating Unit I2C Decoder SW3 SW1SW0 SW2IN2 IN3OUT IN1VEE Circuit description If section Block diagram Vision if Amplifier FPLL, VCO and AFC Standard FeaturesPage Page Adaptive Comb Filter VCT3834A only Video Sync Processing CRT Measurement and Control Page Stand by ConfigurationDescription Application Forced KEY Page Quadrature Mixers ESCPage Page STR-F6654 general description Power supply primary part operationsPage STR-F6654 oscillating operation Overvoltage protection circuit OVP Overcurrent protection function OCPLatch circuit Thermal shutdown circuit TSDTV start-up operations TV normal run and stand-by mode operations Page FBT SC-150 Controlled Rectifier 6V DC High Service Parts List Cord Power Oxide Film 2W 1.2 OHM J Small Semi Fixed CCZB1H561K Cera Carbon Film Metal Film Carbon Comp PA01A RF27 RD-4Z221J Jumper Different Part List by PCB & Micom Version Main PCBUnion PCB Jumper DELExplode View PCB Main PCB Union Schematic DiagramMAIN Schematic DiagramUNION

DSC-3220E/3220L specifications

The Daewoo DSC-3220E/3220L is a noteworthy addition to the lineup of high-efficiency air conditioning solutions, specifically crafted to meet the demands of varying climatic conditions. With a blend of innovative technologies and robust design, these models stand out in the realm of home and commercial air conditioning.

One of the main features of the DSC-3220E/3220L is its efficient cooling performance. The units are built with advanced rotary compressors, which are designed to operate efficiently while providing powerful cooling capabilities. This allows for quick temperature adjustments, making it an ideal choice for those who seek rapid relief from heat.

Another remarkable aspect of the DSC-3220E/3220L is its energy-efficient operation. With a superior Energy Efficiency Ratio (EER), these air conditioning units ensure that energy consumption is minimized without compromising comfort. This not only reduces electricity bills but also contributes to a smaller carbon footprint, making it an environmentally friendly choice.

The units also come equipped with state-of-the-art air filtration technologies. The multi-layer air filters are designed to capture dust, pollen, and other airborne particles, ensuring that the air in the environment remains clean and healthy. This feature is particularly beneficial for allergy sufferers and enhances the overall indoor air quality.

In terms of user convenience, the DSC-3220E/3220L models are engineered with user-friendly controls. Many features, including temperature settings and fan speeds, can be easily adjusted through a remote control or a digital display panel on the unit itself. This ensures that users can customize their comfort levels with minimal effort.

Noise reduction is another critical characteristic of the DSC-3220E/3220L. Both models are designed with silent operation in mind, making them suitable for bedrooms, offices, and other environments where noise can be a distraction. The sound insulation techniques employed help maintain a serene atmosphere while enjoying optimal cooling.

Furthermore, installation of the DSC-3220E/3220L air conditioning systems is straightforward, making them accessible for residential and commercial settings alike. The compact design and versatility in installation options allow these units to fit seamlessly into various spaces without sacrificing performance.

Overall, the Daewoo DSC-3220E/3220L embodies a fine balance of efficiency, technology, and user-centric design, making it a commendable choice for air conditioning needs in diverse settings. With its reliable performance and thoughtful features, it continues to gain popularity among consumers looking for effective climate solutions.