Wayne-Dalton 8300/8500 Torsion Spring Attachment, Securing Door for Spring Windings

Page 12

Left hand cable drum, red

Torsion shaft

Left hand wound, black winding cone (right hand side)

Spring anchor bushing /

center bracket bushing Right hand cable drum, black

Right hand wound, red winding cone (left hand side)

Hook the counterbalance lift cable into the left hand cable drum. Slide the left hand cable drum up against the left hand head plate / end bearing bracket. Counterbalance lift cable should terminate at the 3 o’clock position. Tighten the (2) set screws in the drum to 14-15 ft. lbs. of torque (once set screws contact the shaft, tighten screws one full turn).

Rotate the left hand drum and torsion shaft until counterbalance lift cable is taut. Now attach locking pliers to the torsion shaft and brace locking pliers up against jamb to keep counter- balance lift cable taut.

Repeat for right hand side.

IMPORTANT: Inspect each counterbalance lift cables making sure they are seated properly onto the cable drums and that both counterbalance lift cables have equal tension.

Counterbalance

Left cable drum

lift cable

 

Left hand head plate

Equal spacing

Right hand head plate

/ end bearing

/ end bearing bracket

bracket

 

Torsion shaft

 

Spring anchor bushing /

Spring anchor bracket /

center bracket bushing

center bracket

19

Torsion Spring Attachment

Tools: Step Ladder, Ratchet Wrench, 9/16” Socket, 9/16” Wrench

 

Slide the spring anchor bushing / center bracket bushing into the spring anchor bracket / center bracket. Align the stationary spring cone(s) with the holes in the spring anchor bushing

/center bracket bushing. Secure the torsion spring(s) to the spring anchor assembly / center bracket assembly with (2) 3/8”-16 x 1-1/2” hex head bolts and (2) 3/8”-16 nuts.

IMPORTANT: The spring warning tag supplied must be securely attached to the stationary spring cone in plain view. Should a replacement spring warning tag be required, contact Wayne-Dalton for free replacements.

Stationary spring cone

Spring anchor bracket

Torsion spring

/ center bracket

 

Stationary spring cone

Torsion

springSpring anchor bushing / center bracket bushing

Left hand head

Counterbalance lift

plate / end

cable hooked in

bearing bracket

cable drum

Left end

Jamb

bearing

bracket

 

Locking pliers

 

Counterbalance

 

lift cable

 

Left cable

Torsion

shaft

drum

 

Set

 

screws

 

Torsion spring

(1)

3/8”-16

Nut

 

 

 

 

 

 

 

 

 

06/24

/2010

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REV2

from

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1020

 

 

Prod.

-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

81

 

 

tag

for

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

periodically

tag

 

 

 

tools

 

 

 

 

-

 

 

 

 

 

 

 

neededreplacement

over

this

 

 

propermade

by

 

parts

of

 

to

 

 

 

 

 

 

 

 

 

.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

as,

 

a

this

tag

 

 

 

using

be

 

 

other steel

brackparts

 

 

 

 

 

manufacturershould

order

 

paint

 

technicianmust

 

LY

 

 

 

or

 

 

 

 

 

 

 

cover,

or

 

 

ON

 

.

 

such,

springs

 

 

 

 

 

 

 

 

 

inspect

 

 

 

 

 

 

 

 

fasteners

or

as

 

 

 

 

 

 

door

and

shouldremove

 

 

 

.

 

repairs

 

system

 

remove

 

 

 

TH

.

USE

the

user

 

T

 

 

 

 

door

systemsor

 

 

blocks,

 

or

 

 

 

 

 

CA

 

legibilityuct

NO

 

 

 

 

 

 

 

 

wood

 

connected

 

 

 

 

 

DEA

 

AN

 

 

DO

 

 

instructions

 

 

 

are

repair,

 

 

 

 

Y

C

 

 

 

 

 

 

 

Adjustments

counterbalancecables, springsadjust

 

 

 

 

 

 

 

 

 

 

 

 

and trained

 

 

 

 

 

 

 

 

 

 

 

 

 

OR

 

 

 

 

 

 

 

 

 

 

 

 

the ets,

 

NOT

 

 

 

 

 

INJUR

 

TENSION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

whichDO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SERIOUS

SPRING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HIGH

 

 

 

 

 

Spring warning tag

Stationary spring cone(s)

(1)3/8”-16 x 1-1/2” Hex head bolt

Torsion

spring

21

Securing Door for Spring Winding(s)

Tools: Vice Clamps

 

With the door in the fully closed position, place vice clamps onto both vertical tracks just above the third track roller. This is to prevent the garage door from rising while winding springs.

WARNING

Failure to place vice clamps onto vertical track can allow door to raise and cause severe or fatal injury.

(1) 3/8”-16

 

Nut

 

 

(1) 3/8”-16 x 1-1/2”

Spring anchor assembly / center bracket assembly

Hex head bolt

20

Counterbalance Lift Cables

Tools: Step Ladder, Locking Pliers, 3/8” Wrench

 

Starting on the left hand side, thread the counterbalance lift cable up and around the front side of the left hand cable drum.

IMPORTANT: Verify that there are no counterbalance lift cable obstructions.

12

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,

refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 8300/8500 B l e O f C o n t e n t sRepresentations of the door parts. Each specific door E3. Lock SectionI2.K2 Right Hand Head Plate / End Bearing BracketImportant Safety Instructions Tools Required Headroom Requirements Bottom sectionBottom weather seal Backroom Page Tools Power drill,7/16 Socket driver Graduated Hinge AttachmentLift Handles Step PlateBottom Section Vertical TracksStacking Sections Tools Level, Wooden shims if necessaryTop Section Drawbar Operator BracketHorizontal Tracks Follow the corresponding step belowAdjusting Top Fixtures Torsion Spring AssemblySpring Anchor Bracket / Center Bracket Head Plates / End Bearing BracketsTorsion Spring Attachment Securing Door for Spring WindingsTools Vice Clamps Winding Springs Rear Back HangsCeiling member 16-18 x 1-1/4 Parallel to doorTools Power drill, 7/16 Socket driver, Tape measure Tools Power drill, 1/8 Drill bit, Tape measureTrolley Arm Hookup Side LockFollowing cleaning solution is recommended Using an electric openerImportant Do not use a pressure washer on your garage door Surface preparation for paintingPage Warranty Lifetime Limited Warranty Models 8300
Related manuals
Manual 26 pages 49.6 Kb

8300/8500 specifications

Wayne-Dalton has established itself as a leader in the garage door industry, and their Model 8300/8500 series exemplifies their commitment to quality and innovation. These models are designed for residential homeowners seeking a combination of security, energy efficiency, and aesthetic appeal.

The Wayne-Dalton 8300 model is crafted with a steel construction that prioritizes durability and low maintenance. It features a unique embossed design that mimics the look of real wood, allowing homeowners to achieve a classic appearance without the upkeep. The garage doors come with a variety of color options, enabling customers to select a finish that harmonizes with their home’s exterior.

The 8500 model, on the other hand, introduces superior insulation properties. Constructed with two layers of galvanized steel and a core filled with polystyrene insulation, the 8500 ensures better energy efficiency. This feature is particularly beneficial for homeowners in regions with extreme temperatures, as it helps maintain a consistent indoor environment while reducing energy costs.

Both the 8300 and 8500 models prioritize security features. Wayne-Dalton incorporates a unique locking mechanism and optional security codes to deter unauthorized access. Additionally, the lightweight design aids in smooth operation, reducing wear and tear on the garage door opener.

Technology is another focal point for the Wayne-Dalton line. Both models are compatible with the latest smart home technology, enabling seamless operation via mobile apps. Homeowners can receive notifications, monitor the garage door’s status, and control it remotely, enhancing convenience and peace of mind.

Another notable characteristic is the quiet operation of both models, thanks to their well-engineered torsion spring system. This feature minimizes noise during opening and closing, making them an ideal choice for attached garages where sound can disrupt daily life.

Wayne-Dalton also offers a variety of window options for the 8300/8500 series, allowing homeowners to customize their doors further, adding natural light while maintaining privacy. The options include decorative glass and traditional window placements.

In summary, the Wayne-Dalton 8300/8500 garage doors deliver a perfect blend of aesthetics, durability, and energy efficiency. With advanced technologies, reinforcing security, and exceptional insulation properties, these models cater to the modern homeowner's needs, solidifying Wayne-Dalton’s reputation for excellence in the garage door market.
Top Page Image Contents